PDA

View Full Version : AR Picture Thread



Pages : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 [20] 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132

Mega
03-18-10, 20:25
Are they ever 'done' ? :)

theJanitor
03-18-10, 20:32
You sure that's an LMT upper?

exactly what i was thinking. never seen a standard LMT middy, much less a non-MRP without a standard FSB

fatboyR6
03-18-10, 20:36
You sure that's an LMT upper?

Its a custom build, it has a LMT forged upper receiver with a Match Grade Wilson LMT cut barrel with M4 feed ramps,l with a custom built low-pro gas block. I have a Troy TRX Extreme coming for it.

Why do you question it? Did I get ripped off? I'm new to this so any advise would be awesome!!!

I purchased it from Andy at M&A Parts Inc. New

theJanitor
03-18-10, 20:38
Did I get ripped off?

Match Grade Wilson LMT cut barrel with M4 feed ramps

never heard of this before

fatboyR6
03-18-10, 20:49
never heard of this before

This is what I was told it is:

Our uppers are from Lewis Machine and Tool (LMT). Our barrels are Wilson Match /Rock /Match Grade 4140 Chrome Moly. LMT cuts, finishes and chambers the barrels. LMT assembles, times, headspaces, chambers and function test fires each barreled upper (not every third or fifth one as some suppliers might) and all of the other minor parts included are from current US Govt contract machine shops. The same first-rate US Govt contractor that we have always used for the bolt/carrier assemblies is still our supplier. They prefer anonymity. While we absolutely stand by and attest to the above, know that most of our component parts are "sanitized", that is- without marks, for obvious reasons when you consider the nature of the needs of the larger section of our customer base

The upper looks good to me. It fits awesome on my Spikes lower and the color is exactly the same.

molsen
03-18-10, 20:55
Its a custom build, it has a LMT forged upper receiver with a Match Grade Wilson LMT cut barrel with M4 feed ramps,l with a custom built low-pro gas block. I have a Troy TRX Extreme coming for it.

Why do you question it? Did I get ripped off? I'm new to this so any advise would be awesome!!!

I purchased it from Andy at M&A Parts Inc. New

Cool. I've never heard that before either. I was just wondering for the same reasons mentioned. If you say it is, then that's good enough for me.:D

JonnyVain
03-18-10, 22:29
Primary Arms fixed 4x reticle (or reticule for the snobs ;))

http://farm5.static.flickr.com/4026/4444057961_495c5ef2df_b.jpg

http://farm3.static.flickr.com/2711/4444056563_1f0589541a_b.jpg

Kiwi
03-19-10, 00:20
Primary Arms fixed 4x reticle (or reticule for the snobs ;))

http://farm5.static.flickr.com/4026/4444057961_495c5ef2df_b.jpg

http://farm3.static.flickr.com/2711/4444056563_1f0589541a_b.jpg

Looks like a Pic off an F-14 facing the landing strip OF USS NIMITZ? :p

Stickman
03-19-10, 01:50
http://militarytimes.com/blogs/gearscout/wp-content/blogs.dir/5/files/new-oakley-si-tactical-fr-glove/stck0065-800-mt.jpg

Preach
03-19-10, 15:31
Colt 6920
Eotech 551
m900a
DD Omega Rail
Vltor Clubfoot
Troy BUIS
Laserlyte
Hogue Grip

4500

Fyrhazzrd
03-19-10, 17:12
http://i132.photobucket.com/albums/q37/bkpickell/My%20M4%20Garbine/P1010417.jpg
http://i132.photobucket.com/albums/q37/bkpickell/My%20M4%20Garbine/P1010418.jpg

RRA Lower
DD Upper
BCM Auto BCG
Olympic Arms M4 Stainless Barrel
Double Star handguard
MI flip up rear sight

Preach
03-19-10, 17:37
My Piston
LWRC M6A2
Aimpoint comp M4s
M900a
Magpul ACS
Hogue Grip
4501

4502

JTrusty
03-19-10, 17:41
Playing with a new light setup ( unfortunately, harsh sunshine today ) ...

http://www.gearsector.com/img/misc/forum/gsr/sbr/09.jpg

http://www.gearsector.com/img/misc/forum/gsr/sbr/10.jpg

PriestFoxley
03-19-10, 20:28
Colt 6920
Eotech 551
m900a
DD Omega Rail
Vltor Clubfoot
Troy BUIS
Laserlyte
Hogue Grip

P.S. How do I get my pic to just show up in the post and not have to be an attachment?:confused:

who cares? you got a nice rifle, and I have always been partial to hogue berettas with rails.

HeavyDuty
03-19-10, 20:34
who cares?


P.S. How do I get my pic to just show up in the post and not have to be an attachment?:confused:

That was helpful. :rolleyes:

Preach, look at the URL for your pic attachments. Then go back and edit your posts - paste in that URL wrapped in IMG tags. Here, hit reply to my post and you'll see how I made this pic of yours display in-line:

https://www.m4carbine.net/attachment.php?attachmentid=4500&d=1269030487

tr1kstanc3
03-19-10, 20:36
Playing with a new light setup ( unfortunately, harsh sunshine today ) ...

Jason,

Would you mind detailing your light rig setup. Looking good.

Thanks.

Joeywhat
03-19-10, 21:44
http://i79.photobucket.com/albums/j151/joeywhat/IMG_6278.jpg

justin_247
03-19-10, 21:56
http://i132.photobucket.com/albums/q37/bkpickell/My%20M4%20Garbine/P1010417.jpg
http://i132.photobucket.com/albums/q37/bkpickell/My%20M4%20Garbine/P1010418.jpg

RRA Lower
DD Upper
BCM Auto BCG
Olympic Arms M4 Stainless Barrel
Double Star handguard
MI flip up rear sight

What is the mounting system for this handguard? It looks a lot like the one used on the DD Omega series...

justin_247
03-19-10, 22:02
White Oak upper
ADCO Custom Cruiser barrel
Bravo Company BCG
Troy MRF-R
Magpul MOE stock, Pmags, and XT rail covers
Primary Arms 4x scope
Boonie Packer 2pt quick adjust sling.
AAC Blackout FH
DD Rear sight (on bottom of rail)
Stark Equipment SE-1 pistol grip.
Spike's Tactical ST-T2 buffer
Fender Hot Rod Deluxe White Lightning.

http://farm5.static.flickr.com/4002/4441625891_6d851ab094_b.jpg
http://farm5.static.flickr.com/4046/4441633227_85ea5d70b6_b.jpg
http://farm5.static.flickr.com/4062/4442409604_bb58548e79_b.jpg
http://farm5.static.flickr.com/4053/4442411640_cc2ae65703_b.jpg
http://farm5.static.flickr.com/4017/4442407778_a98ace5c79_b.jpg
http://farm5.static.flickr.com/4040/4442402076_8755675f17_b.jpg
http://farm3.static.flickr.com/2765/4442400114_0f28c0dcd3_b.jpg
http://farm3.static.flickr.com/2765/4441623919_38241b7d72_b.jpg

UM, why is your rear BUIS where it is?

perna
03-19-10, 23:05
UM, why is your rear BUIS where it is?

It doubles as a handstop.

justin_247
03-19-10, 23:23
It doubles as a handstop.

LOL! "Doubles"... it isn't exactly doing anything there *except* act as a handstop.

cop1211
03-20-10, 00:03
It doubles as a handstop.

:eek:

bkb0000
03-20-10, 00:06
i'd be bouncing that rear BUIS/handstop off the gravel/concrete/dirt/mud/grass every time i slid into prone. not a good place for a piece of precision instrumentation.

WillardCW4
03-20-10, 00:10
http://i79.photobucket.com/albums/j151/joeywhat/IMG_6278.jpg

Where did you get that dust cover...? Epic.

Hoss356
03-20-10, 01:36
Who's down with the LBC?!

http://img97.imageshack.us/img97/1703/dsc00915at.jpg (http://img97.imageshack.us/i/dsc00915at.jpg/)

rsoakley
03-20-10, 03:49
I used a piece of heavy duty lace I picked up at a lace outlet store.

What Jeff meant was,... 'tactical lace'

Where's "Pineland?"

Joeywhat
03-20-10, 06:50
Where did you get that dust cover...? Epic.

Somewhere on Gunbroker. There were a couple other Team American references and some others as well.

Moose-Knuckle
03-20-10, 07:15
Where's "Pineland?"

http://www.usatoday.com/news/military/2009-07-04-pineland-patriots_N.htm

RogerinTPA
03-20-10, 09:38
It doubles as a handstop.

ROFLMFAO!:p

JonnyVain
03-20-10, 09:47
ROFLMFAO!:p

I had no other place to put it with my fixed 4x... I've seen pics of marines putting their carry handles under the rail for storage with their acogs on.

It doesn't matter anyway. My 4x is for the range. My red dot stays on for HD.

Rusty_Shackleford
03-20-10, 10:31
http://i555.photobucket.com/albums/jj475/Cansler_Tactical/Chatterbox-Blackie.jpg

Stickman
03-20-10, 10:32
http://stickman.rainierarms.com/galleries/Magpul%20V/STCK0048-A-1024-Stick.jpg

RustedAce
03-20-10, 10:42
http://img294.imageshack.us/img294/5263/p3170026.jpg

newyork
03-20-10, 12:13
http://img294.imageshack.us/img294/5263/p3170026.jpg

Ok, now I'm starting to hate you. Great rifles ya got there as usual man.

high plain drifter
03-20-10, 12:44
http://i623.photobucket.com/albums/tt312/combatgunner/champion/IMG_0382.jpg

http://i623.photobucket.com/albums/tt312/combatgunner/champion/IMG_0378.jpg

Caeser25
03-20-10, 12:52
I had no other place to put it with my fixed 4x... I've seen pics of marines putting their carry handles under the rail for storage with their acogs on.

It doesn't matter anyway. My 4x is for the range. My red dot stays on for HD.

I've seen them used as a buis on rails in FRONT of the m68

Jabroni
03-20-10, 13:56
Nice Lower you got there drifter. The boys at SOG would be proud. I stop in there from time to time, so it's cool to see one of there lowers on here.:D How is it? Are you pretty happy with it so far?

tibis3383
03-20-10, 14:27
http://i623.photobucket.com/albums/tt312/combatgunner/champion/IMG_0382.jpg

http://i623.photobucket.com/albums/tt312/combatgunner/champion/IMG_0378.jpg

Great looking rifle you have there Drifter. I've been thinking about using a CASV rail system on a 14.5 middy and after seeing this I probably will. Any plans for an optic?

Semper Fi

Tim

high plain drifter
03-20-10, 15:16
the SOG lower does not like pmags. they dont drop freely at all. but it loves the tangodown mags.

as far as optics go i was thinking about aimpoint's micro T-1. but i dont know what height to get for sure, since the CASV is mounted on the flattop it would be high. i have a another aimpoint but its on another rifle. any other suggestions for optics? im kinda new here. https://www.m4carbine.net/images/smilies/smile.gif

high plain drifter
03-20-10, 15:18
the SOG lower does not like pmags. they dont drop freely at all. but it loves the tangodown mags.

as far as optics go i was thinking about aimpoint's micro T-1. but i dont know what height to get for sure, since the CASV is mounted on the flattop it would already be somewhat higher. i have a another aimpoint but its on another rifle. any other suggestions for optics? im kinda new here.

Sierrahotel83
03-20-10, 16:39
What is the mounting system for this handguard? It looks a lot like the one used on the DD Omega series...

They are not free float handguards, they use the Delta ring which the Omega uses. :D

USAGOLD
03-20-10, 17:49
Some great looking rifles

memberonly
03-20-10, 23:20
some B&W's

http://img441.imageshack.us/img441/4649/47843813.jpg

http://img705.imageshack.us/img705/1205/95932128.jpg

http://img225.imageshack.us/img225/8426/64625067.jpg

justin_247
03-21-10, 07:07
It doubles as a handstop.

Sounds worthless! Please mail it to me for proper disposal.

SeriousStudent
03-21-10, 09:40
Memberonly - Very nice photos, I really like those black and white images.

Thanks for posting them. :)

DWS
03-21-10, 15:05
Updated the Stick a little. Installed a Yankee Hill Tube, KX3, MBUS's etc etc....

So the paint job needed to be reworked. I am very satisfied with the results....

http://i124.photobucket.com/albums/p23/halfacop/101_4769.jpg

http://i124.photobucket.com/albums/p23/halfacop/101_4771.jpg

http://i124.photobucket.com/albums/p23/halfacop/101_4770.jpg

memberonly
03-21-10, 15:18
Memberonly - Very nice photos, I really like those black and white images.

Thanks for posting them. :)

Thanks. Glad that you like those.

Titleist
03-21-10, 15:27
http://farm5.static.flickr.com/4066/4451128531_7a04cdf945_b.jpg

Stickman
03-21-10, 15:35
http://stickman.rainierarms.com/galleries/BCM/STCK0548-1024-Stick.jpg

David Thomas
03-21-10, 15:44
http://img.photobucket.com/albums/v441/DavidThomas/039-1.jpg

glockeyed
03-21-10, 16:11
after a rit dye job.....

http://s-seriesforum.com/albums/projects/ritdye_6.jpg

BufordTJustice
03-21-10, 17:01
http://stickman.rainierarms.com/galleries/BCM/STCK0548-1024-Stick.jpg

Stick, What Micro mount is that?

Looks super-trick and I'm in the market for one for my patrol carbine.

Titleist
03-21-10, 17:02
http://farm5.static.flickr.com/4061/4452233682_5b7524c03c_b.jpg

aftermath686
03-21-10, 17:23
Damn Titleist, is that four PEQ15s now!?!? Also any chance you can get a shot from the other side of the sr25, showing the light mount a bit better, as well as maybe one from the front of the gun. Is that one of the new off-set Scout light mounts? Does it interfere with the vis laser?

Thanks

Titleist
03-21-10, 17:26
Damn Titleist, is that three PEQ15s now!?!? Also any chance you can get a shot from the other side of the sr25, showing the light mount a bit better, as well as maybe one from the front of the gun. Is that one of the new off-set Scout light mounts? Does it interfere with the vis laser?

Thanks

Here you go:

http://farm3.static.flickr.com/2710/4452233306_34100f0bc0_b.jpg

http://farm5.static.flickr.com/4044/4452233572_1415451903_b.jpg

tr1kstanc3
03-21-10, 17:32
http://farm3.static.flickr.com/2696/4451572519_110812e6e1_b.jpg

aftermath686
03-21-10, 17:39
Here you go:


Thanks Bud. Any chance you can let me in on who makes that mount? And does the light block the visible laser in that spot?

Thanks again

Titleist
03-21-10, 17:49
No it doesn't really block the laser, there's some splash from the red laser, but it's minimal. The mount is made by Danger Close Consulting.

aftermath686
03-21-10, 18:00
That's what I thought, but I had seen you in the Gear sector thread so I wasn't sure.

Thanks for the heads up.

Stickman
03-21-10, 18:48
Stick, What Micro mount is that?

Looks super-trick and I'm in the market for one for my patrol carbine.


Fantastic mount from KAC, check out the below writeup at Military Times for more info than you want to know.... :D

http://militarytimes.com/blogs/gearscout/2009/11/17/kac-mounts/



http://militarytimes.com/blogs/gearscout/wp-content/blogs.dir/5/files/kac-t-1-mount/img_0887-800-mt.jpg




http://militarytimes.com/blogs/gearscout/wp-content/blogs.dir/5/files/kac-t-1-mount/img_0885-800-mt.jpg

VA_Dinger
03-21-10, 19:06
Updated the Stick a little. Installed a Yankee Hill Tube, KX3, MBUS's etc etc....

So the paint job needed to be reworked. I am very satisfied with the results....

http://i124.photobucket.com/albums/p23/halfacop/101_4769.jpg

http://i124.photobucket.com/albums/p23/halfacop/101_4771.jpg

http://i124.photobucket.com/albums/p23/halfacop/101_4770.jpg

Nice!

I like the paint job.

BufordTJustice
03-21-10, 19:42
Fantastic mount from KAC, check out the below writeup at Military Times for more info than you want to know.... :D

http://militarytimes.com/blogs/gearscout/2009/11/17/kac-mounts/



http://militarytimes.com/blogs/gearscout/wp-content/blogs.dir/5/files/kac-t-1-mount/img_0887-800-mt.jpg




http://militarytimes.com/blogs/gearscout/wp-content/blogs.dir/5/files/kac-t-1-mount/img_0885-800-mt.jpg

Thank you for your prompt reply, good sir. I'm already neck-deep in the write up. ;) I may NEED one of these.

mark5pt56
03-21-10, 20:02
you'll see this agan soon

IDF

Wow,finally got everything together.

Lower-NDS blem––really blemed now!
Lower parts-used anything that was spare taken out of past upgrades, etc
Stock-old Eagle commercial tube and 2 position.
Upper-old Colt beater from Dawg180
BCG, CMT I think, new CH
Barrel- Daniel Defense 16" pencil cut down and A1 pin/wel by Adco
Sling from M1sniper
IDF bands
And special refinish job by mhttp://www.ar15.com/images/smilies/icon_smile_cool.gif

Got her zero'ed today and hd some fun shooting.


http://img.photobucket.com/albums/v509/mark5pt56/003-11.jpg
http://img.photobucket.com/albums/v509/mark5pt56/004-9.jpg
http://img.photobucket.com/albums/v509/mark5pt56/005-6.jpg
http://img.photobucket.com/albums/v509/mark5pt56/006-4.jpg

Stickman
03-21-10, 22:00
mark5pt56,

Sex appeal of the weapon is off the chart.

subzero
03-21-10, 22:04
That is gorgeous, Mark. I've wanted one of those for the last 15 years or so.

Quib
03-21-10, 22:29
Looks great Mark!

pcardinal42
03-21-10, 23:17
Hey everyone first timer here. I've been researching the AR world for a few months now and put together my first one Saturday and got it to the range today. No disappointment here at all.

http://s245.photobucket.com/albums/gg64/pcardinal42/?action=view&current=IMG_0004-1.jpg

http://s245.photobucket.com/albums/gg64/pcardinal42/?action=view&current=IMG_0003.jpg

Specs are: 5.56/.223, 1:7 twist, 16" CMMG upper, ProMag BUIS, Del-ton complete Lower receiver, I think its a Magpul Stock 6 position but it doesn't have any markings on it.

YATYAS
03-22-10, 00:35
Before:
https://www.m4carbine.net/picture.php?albumid=214&pictureid=1012

After (so far):
https://www.m4carbine.net/picture.php?albumid=214&pictureid=1010

Stickman
03-22-10, 00:43
BCM Upper/ BCM Lower



http://stickman.rainierarms.com/galleries/BCM/STCK0605-1024-Stick.jpg



http://stickman.rainierarms.com/galleries/BCM/STCK0608-1024-Stick.jpg

Lawdog-1
03-22-10, 06:38
Stickman, what brand mount is that Aimpoint mounted on ?

fatboyR6
03-22-10, 15:58
Spikes lower, DPMS LPK, custom upper M4 feed ramps middy Match grade HBAR 1/9, TroyTRX Extreme 11" rail, BAD Lever, BCM Mod 4, Ergo grip with gapper, Magpul ACS, Spikes ST-T2 buffer, Young MFG. Match Grade BCG, Grip-Pod military grade model.

This is my first build and have done all the assembly except the upper dust cover and FWD assist.

http://i246.photobucket.com/albums/gg108/fatboyR6/TroyTRX1.jpg

http://i246.photobucket.com/albums/gg108/fatboyR6/TroyTRX2.jpg

http://i246.photobucket.com/albums/gg108/fatboyR6/TroyTRX3.jpg

Pulsar
03-22-10, 17:08
Not a carbine, but:

http://img211.imageshack.us/img211/5113/img0551s.jpg

BufordTJustice
03-22-10, 19:47
Stickman, what brand mount is that Aimpoint mounted on ?

Lawdog, I already asked the Stickman the exact same question. ;) It's a KAC mount and it's super trick. They have it on sale right now for $132 at their store.

RetreatHell
03-22-10, 19:48
Been a while since I posted in this thread, even forgot to put a mag in for the pics.

Got my BCM 14.5" middy AND my Surefire suppressor late last week! I'll get around to taking better pics of it eventually, but these will have to do for now. I haven't shot either yet, but will this week.


http://i685.photobucket.com/albums/vv219/RetreatHell/BCM%20SBR/BCM%20Middy%20SBR/IMG_3056.jpg

http://i685.photobucket.com/albums/vv219/RetreatHell/BCM%20SBR/BCM%20Middy%20SBR/IMG_3080.jpg

Semper Fi,

-Paul

aftermath686
03-22-10, 20:29
Paul great taste in kit, gun looks awesome. Let us know how it shoots.:cool:

SpartanArms
03-22-10, 21:17
Paul,

Nice blaster there brother. :D How are you liking the SF Mini-Scout light?

LMarshall73
03-22-10, 21:37
Latest configuration of my trio (with changes already in the works):

http://img36.imageshack.us/img36/6798/sprspecs.jpg

http://img90.imageshack.us/img90/971/m4geryspecs.jpg

http://img697.imageshack.us/img697/6274/pistolspecs.jpg

Oh, and if you're curious as to WTF is on the rail on the M4 and the pistol, a write up is in the works. :D

texas12
03-22-10, 22:17
Been a while since I posted in this thread, even forgot to put a mag in for the pics.

Got my BCM 14.5" middy AND my Surefire suppressor late last week! I'll get around to taking better pics of it eventually, but these will have to do for now. I haven't shot either yet, but will this week.



Semper Fi,

-Paul

Just got my DD MK18 rail on my gun the other day, it's a sweet rail aint it.:D

Titleist
03-22-10, 23:29
http://farm3.static.flickr.com/2787/4456530900_8d7975b84a_b.jpg

RetreatHell
03-22-10, 23:44
Dude! Did you REALLY have to post that badass pic on the same page as mine? I mean, seriously, man?

You're stealin' my thunder, bro...

That is a sweet ****ing pic though;)

Semper Fi,

-Paul

Titleist
03-22-10, 23:46
Paul, did I not WARN you I had something cool to post later on today?!

Sorry, brah! :D

bruce_hxc
03-23-10, 00:02
Got my BCM 14.5" middy AND my Surefire suppressor late last week! I'll get around to taking better pics of it eventually, but these will have to do for now. I haven't shot either yet, but will this week.


http://i685.photobucket.com/albums/vv219/RetreatHell/BCM%20SBR/BCM%20Middy%20SBR/IMG_3056.jpg


This is the hotness.

How's the balance with the can vs without? Maybe a little review of the upper/brake/suppressor when you get a chance?

RetreatHell
03-23-10, 01:11
Paul,

Nice blaster there brother. :D How are you liking the SF Mini-Scout light?

Thanks, man! I'm really diggin' the new mini-scout. It seems to take up less space and be less bulky than my X300s I run. Weight-wise it's practically the same as the X300. The beam is slightly more focused than the X300, but both of their throws are great. They both light up the target (too) easily at 100 yards.

I'd highly recommend either weaponlight, although I do now personally prefer the M300 mini-scout. I need to buy a FDE one now:D

Semper Fi,

-Paul

RetreatHell
03-23-10, 01:36
Just got my DD MK18 rail on my gun the other day, it's a sweet rail aint it.:D

Although yours is designed a little different than mine, color-wise hell yeah, I really like it! I think it looks great.



This is the hotness.

How's the balance with the can vs without? Maybe a little review of the upper/brake/suppressor when you get a chance?

Thanks, man!

The balance sucks with the can mounted, as it just makes it so damn front heavy. But I mainly got the suppressor to run on my SBR. For this upper and my 16" upper, I'll mainly only shoot them with the can on when I have a rest. I simply can't handle that much front-heaviness for more than a few minutes of training and running it hard. Although it's difficult for me to judge since I'm in a chair, I think most able-bodied shooters would be able to run this setup in a 2-3 day carbine course, so long as they're in shape. But after a while it'll wear anyone out if they're not running it on an SBR.

I won't be able to shoot this upper with the can mounted for a few weeks though. I need to have the muzzle device permanently installed first. Right now I just have it on there with a crush washer, so that I can make damn sure I want the brake pinned on there for good or not, or go with the SF flash hider instead. That's a registered SBR lower it's sitting on in the pics, but it makes no sense to me (for my personal application) to have an actual 14.5" SBR when it's already just over 16" with the brake installed.

But I'll post an update after I get a chance to really run the upper a little bit.

Pic thread:

http://i685.photobucket.com/albums/vv219/RetreatHell/BCM%20SBR/BCM%20Middy%20SBR/IMG_3089.jpg

Semper Fi,

-Paul

Lee Indy
03-23-10, 02:38
http://img697.imageshack.us/img697/6274/pistolspecs.jpg

Oh, and if you're curious as to WTF is on the rail on the M4 and the pistol, a write up is in the works. :D

WTF is that forward sling attachment point on the pistol

Hoss356
03-23-10, 02:50
Titleist, I have to say I really enjoy your photography on here and TOS but I just read your graphic design resume and I really think you're cheating us now!:D Keep up the great shots, I like your lighting set up on the one you just posted, so lets see some more creative lighting techniques.

bruce_hxc
03-23-10, 03:16
Thanks, man!

The balance sucks with the can mounted, as it just makes it so damn front heavy. But I mainly got the suppressor to run on my SBR. For this upper and my 16" upper, I'll mainly only shoot them with the can on when I have a rest. I simply can't handle that much front-heaviness for more than a few minutes of training and running it hard. Although it's difficult for me to judge since I'm in a chair, I think most able-bodied shooters would be able to run this setup in a 2-3 day carbine course, so long as they're in shape. But after a while it'll wear anyone out if they're not running it on an SBR.

I won't be able to shoot this upper with the can mounted for a few weeks though. I need to have the muzzle device permanently installed first. Right now I just have it on there with a crush washer, so that I can make damn sure I want the brake pinned on there for good or not, or go with the SF flash hider instead. That's a registered SBR lower it's sitting on in the pics, but it makes no sense to me (for my personal application) to have an actual 14.5" SBR when it's already just over 16" with the brake installed.

But I'll post an update after I get a chance to really run the upper a little bit.

Semper Fi,

-Paul


Thanks for the details! Again, great looking setup.

I've been kicking around the idea of something similar so I definitely look forward to your updates.

God Bless,

I'll stop interrupting the pic thread now, lol.

Cameron
03-23-10, 03:53
you'll see this agan soon

IDF

http://img.photobucket.com/albums/v509/mark5pt56/006-4.jpg

That is really very nice!

Cameron

LMarshall73
03-23-10, 09:15
WTF is that forward sling attachment point on the pistol

:D

It's a hybrid of sorts that I came up with. I'm putting a write up together.

Stickman
03-23-10, 10:08
BCM 14.5 Middy overview (http://www.weaponevolution.com/forum/showthread.php?p=19139#post19139)

http://stickman.rainierarms.com/galleries/BCM/STCK0717-1024-Stick.jpg

edwin907
03-23-10, 11:15
http://bellsouthpwp.net/e/d/edwin907/MRP-22a.jpg



http://bellsouthpwp.net/e/d/edwin907/USO4.jpg

LMarshall73
03-23-10, 12:56
WTF is that forward sling attachment point on the pistol

Write up is HERE (https://www.m4carbine.net/showthread.php?t=50184)

Boss Hogg
03-23-10, 14:52
Barrel is a 16" Centurion midlength, with a TA11H ACOG.

http://i217.photobucket.com/albums/cc295/B055H0GG/DSCF0317small.jpg

http://i217.photobucket.com/albums/cc295/B055H0GG/DSCF0322small.jpg

djegators
03-23-10, 17:27
Added a few goodies to the Noveske Recce:


Magpul UBR, AFG, and XM rail covers:


http://i42.tinypic.com/28wbx2.jpg

TwoSqueeze
03-23-10, 18:09
http://img511.imageshack.us/img511/9268/sbr1.jpg

http://img534.imageshack.us/img534/8363/sbr2.jpg

http://img716.imageshack.us/img716/5835/sbr3.jpg

http://img716.imageshack.us/img716/1151/sbr4.jpg

http://img716.imageshack.us/img716/6990/sbr5.jpg

Yes my photo Fu is weak.

-TS

Rusty_Shackleford
03-24-10, 09:45
http://img511.imageshack.us/img511/9268/sbr1.jpg

http://img534.imageshack.us/img534/8363/sbr2.jpg

http://img716.imageshack.us/img716/5835/sbr3.jpg

http://img716.imageshack.us/img716/1151/sbr4.jpg

http://img716.imageshack.us/img716/6990/sbr5.jpg

Yes my photo Fu is weak.

-TS
Specs please?
pic thread:
http://i555.photobucket.com/albums/jj475/Cansler_Tactical/chatterbox-Blackie2.jpg (http://i555.photobucket.com/albums/jj475/Cansler_Tactical/chatterbox-Blackie2.jpg)

RSS1911
03-24-10, 10:20
http://img.photobucket.com/albums/v251/ronssmith/Guns/20100324013a.jpg (http://img.photobucket.com/albums/v251/ronssmith/Guns/20100324013a.jpg)

sadmin
03-24-10, 10:53
http://img511.imageshack.us/img511/9268/sbr1.jpg

Yes my photo Fu is weak.

-TS

Good Looking rifle, WHOOP!

Sierrahotel83
03-24-10, 11:19
Paul now I am jealous I really want one of those iPhone covers.:( It may have been a factor in why I got an iPhone;)

TwoSqueeze
03-24-10, 11:29
Specs please?
pic thread:
http://i555.photobucket.com/albums/jj475/Cansler_Tactical/chatterbox-Blackie2.jpg (http://i555.photobucket.com/albums/jj475/Cansler_Tactical/chatterbox-Blackie2.jpg)

Build information can be found in this thread. (http://m4carbine.net/showthread.php?t=50199)

d90king
03-24-10, 13:32
Been a while since I posted in this thread, even forgot to put a mag in for the pics.

Got my BCM 14.5" middy AND my Surefire suppressor late last week! I'll get around to taking better pics of it eventually, but these will have to do for now. I haven't shot either yet, but will this week.


http://i685.photobucket.com/albums/vv219/RetreatHell/BCM%20SBR/BCM%20Middy%20SBR/IMG_3056.jpg

http://i685.photobucket.com/albums/vv219/RetreatHell/BCM%20SBR/BCM%20Middy%20SBR/IMG_3080.jpg

Semper Fi,

-Paul


Paul, great looking build. I also like the scout ... I use a X300 but am looking at going that route. Great job on the stippling....

d90king
03-24-10, 13:44
you'll see this agan soon

IDF

Wow,finally got everything together.

Lower-NDS blem––really blemed now!
Lower parts-used anything that was spare taken out of past upgrades, etc
Stock-old Eagle commercial tube and 2 position.
Upper-old Colt beater from Dawg180
BCG, CMT I think, new CH
Barrel- Daniel Defense 16" pencil cut down and A1 pin/wel by Adco
Sling from M1sniper
IDF bands
And special refinish job by mhttp://www.ar15.com/images/smilies/icon_smile_cool.gif

Got her zero'ed today and hd some fun shooting.


http://img.photobucket.com/albums/v509/mark5pt56/003-11.jpg
http://img.photobucket.com/albums/v509/mark5pt56/004-9.jpg
http://img.photobucket.com/albums/v509/mark5pt56/005-6.jpg
http://img.photobucket.com/albums/v509/mark5pt56/006-4.jpg



Not sure how to really put it... but there is something very cool about this rifle. Love it. Great work and use of imagination.:cool:

bnanaphone
03-24-10, 21:17
Here is my BCM
http://lh5.ggpht.com/_mdMkiHQASmQ/S6ovop2k8pI/AAAAAAAAAXM/LcNpLxSDjHY/s1024/Helmet.JPG

Here is the Varminter...and a little fog
http://lh6.ggpht.com/_mdMkiHQASmQ/S6ovl1zkZhI/AAAAAAAAAXI/nes20nh4IcA/s1024/varminter.JPG

tr1kstanc3
03-24-10, 22:03
great photos bnanaphone!

J_ROC7
03-24-10, 22:55
http://img511.imageshack.us/img511/9268/sbr1.jpg

http://img534.imageshack.us/img534/8363/sbr2.jpg

http://img716.imageshack.us/img716/5835/sbr3.jpg

http://img716.imageshack.us/img716/1151/sbr4.jpg

http://img716.imageshack.us/img716/6990/sbr5.jpg

Yes my photo Fu is weak.

-TS

I am working on a build that is almost exactly like this one, when you get a chance let us know how she shoots.

djdarkfader
03-24-10, 23:02
it may be kinda plain compared to some of the beautiful rifles pictured in this thread. this is my first AR(which ive wanted for about twenty years, or as soon as i saw the movie platoon as a kid!). i just finished building it last week and have ran about 120 rounds through it. it's a rock river arms stripped lower built up with a DTI 16" chrome lined HBAR A2 upper. the scope's a cheapie until i can afford something a little nicer. i also added the rail under the gas block for options later on down the road. i love my AR and cant wait to build another! thanks for looking.4569

4570

4571

4572

bkb0000
03-24-10, 23:11
damn.. A2 upper and everything. kickin it owd skew.

zeke18
03-24-10, 23:11
Here is my first AR from the beginning:

http://i301.photobucket.com/albums/nn77/zeke42/DSC_0016-nosn.jpg (http://s301.photobucket.com/albums/nn77/zeke42/?action=view&current=DSC_0016-nosn.jpg)

To it's completion today.

http://i301.photobucket.com/albums/nn77/zeke42/IMG_4336.jpg (http://s301.photobucket.com/albums/nn77/zeke42/?action=view&current=IMG_4336.jpg)

Sorry about the photos I'll try and get some better ones up later when I can take some closer shots. This is my first AR I have owned and the first one I have shot. Put it together today after the UPS man dropped off my new BCM Lightweight Midlength upper, I only have about 100 rounds through it but love the rifle. Thanks to everyone on the site for letting me lurk and learn.

BCM: Lightweight 16" Midlength Upper, BCG, Mod. 4 Charging Handle, Buffer Tube Assembly
Essential Arms Lower
Magpul MOE pistol grip and stock
RRA: LPK, handguards (to be replaced by Midlength MOE handguards)
Daniel Defense A1.5 Rear Sight
Blue Force Gear 2-point Victory Sling (not pictured)

Stickman
03-25-10, 01:46
http://stickman.rainierarms.com/galleries/BCM/STCK0607-1024-Stick.jpg

fls9497
03-25-10, 02:33
Just needs an Aimpoint T-1 on a GG&G mount and I'm done
http://i157.photobucket.com/albums/t50/caligrown619/multicool2.jpg (http://s157.photobucket.com/albums/t50/caligrown619/?action=view&current=multicool2.jpg)

RetreatHell
03-25-10, 03:05
http://i685.photobucket.com/albums/vv219/RetreatHell/BCM%20SBR/BCM%20Middy%20SBR/IMG_3137.jpg (http://i685.photobucket.com/albums/vv219/RetreatHell/BCM%20SBR/BCM%20Middy%20SBR/IMG_3137.jpg)

Semper Fi,

-Paul

aftermath686
03-25-10, 03:25
**** I thought it was nice before, you managed to make it better! Nice PEQ15!

Rig looks great!

JBecker 72
03-25-10, 07:28
http://i685.photobucket.com/albums/vv219/RetreatHell/BCM%20SBR/BCM%20Middy%20SBR/IMG_3137.jpg (http://i685.photobucket.com/albums/vv219/RetreatHell/BCM%20SBR/BCM%20Middy%20SBR/IMG_3137.jpg)

Semper Fi,

-Paul

sick blaster :)

ForTehNguyen
03-25-10, 09:36
BCM 16" Middy Lightweight Upper
Cavalry Arms CAV-15 MkII lower receiver
G&R LPK + Car Buffer
Magpul BAD
Magpul MBUS Rear
Delton middy handguard (waiting for MOE middy FDE)
Cavalry Arms Coyote Sling for MkII Lowers

Later on probably gonna get a Primary Arms H-1 Clone

BTW Cav Arms coyote brown matches with the rest of the industry's FDE, not Cav Arms FDE. Says so on their website

http://i293.photobucket.com/albums/mm49/PreludePowerR/7a8db0a4.jpg

http://i293.photobucket.com/albums/mm49/PreludePowerR/b77e2872.jpg

d90king
03-25-10, 11:23
http://i685.photobucket.com/albums/vv219/RetreatHell/BCM%20SBR/BCM%20Middy%20SBR/IMG_3137.jpg (http://i685.photobucket.com/albums/vv219/RetreatHell/BCM%20SBR/BCM%20Middy%20SBR/IMG_3137.jpg)

Semper Fi,

-Paul

Show off! What are ya trying to be like Ansel Adams..?:D Looks great, hows it shoot?

bkb0000
03-25-10, 12:10
BCM 16" Middy Lightweight Upper
Cavalry Arms CAV-15 MkII lower receiver
G&R LPK + Car Buffer
Magpul BAD
Magpul MBUS Rear
Delton middy handguard (waiting for MOE middy FDE)
Cavalry Arms Coyote Sling for MkII Lowers

Later on probably gonna get a Primary Arms H-1 Clone

BTW Cav Arms coyote brown matches with the rest of the industry's FDE, not Cav Arms FDE. Says so on their website

weight?? that was the point of the build, afterall, right?

RetreatHell
03-25-10, 13:23
Thanks guys, I appreciate the nice comments;)



... Looks great, hows it shoot?

Although I haven't yet run it with this particular suppressor, it runs great! It's got a smaller gas port, set up for mostly suppressed use. It'll run pretty well without a can mounted, depending on ammo. It has much less recoil than a normal suppressed SBR, and less blowback too. When firing unsuppressed, it actually has less recoil than a 16" middy upper (FYI, it was a one-time only custom port job done for me by a couple of good friends of mine in the industry;)).

Here's a video of it in use. You never actually see the carbine, just the impacts on steel 100 yards downrange, caught by a camera with a PVS-14 mounted in front of it. All of the shots that my IR laser/illuminator is just right of the target are from me firing this SBR. Neither my aimpoint T-1 or PEQ-15 were BZO'd for this carbine b/c I did a switch-a-roo at the last minute. Once I figured out that my rounds were impacting low and left just off the target, I compensated by shooting high right just off the target. I had a PVS-14 mounted behind my aimpoint, so I would also just use the illum function to light up the target and use my T-1 on NV setting to engage, which worked very well. It was a friggin' blast!

http://www.youtube.com/watch?v=xDxzYIBbPTg

The shots you see without any IR laser/illum are from a 6.8 upper using a 4X NV scope, and there's also one long full auto burst fired from a .22 upper sitting on an M16 lower.

Semper Fi,

-Paul

aftermath686
03-25-10, 17:53
Cool video Paul! What are you doing for activation of the PEQ15? Thought about the SF dual activation switch for that 12oclock position?

Titleist
03-25-10, 18:03
Unless you have a LOT of rail space I'd suggest just mounting the PEQ forward, and rolling your thumb up and using the TOP FIRE button.

The dual pad is nice, but it required the use of KAC T-1 mounts otherwise I had to push my T-1/Larue combos way back to accommodate that setup.

NCPolice555
03-25-10, 18:49
Here's my Colt Law Enforcement 6940
http://i3.photobucket.com/albums/y56/FatalVision555/my%20Guns/100_1144.jpg

Nothing outrageous, but perhaps it's just the Mrine in me but I love how this shoots, and for me it had to be a Colt.

And here is the rest of the collection....


http://i3.photobucket.com/albums/y56/FatalVision555/my%20Guns/013.jpg

aftermath686
03-25-10, 18:51
Unless you have a LOT of rail space I'd suggest just mounting the PEQ forward, and rolling your thumb up and using the TOP FIRE button.

The dual pad is nice, but it required the use of KAC T-1 mounts otherwise I had to push my T-1/Larue combos way back to accommodate that setup.

I may be wrong but it looks like he might be able to squeeze it in by replacing the SR07. I disagree with moving the PEQ forward however. I used to run my PEQ forward like you say but realized (thanks to some people much more hi-speed than I) that I should not compromise my grip of the weapon. Optimally, one should configure the accessories to work around your own proper grip. With me I am very high on the fore-end and my hand was hitting the PEQ when in the forward position, so I didn't have quite the control I could have. Another option for him would be to leave the setup as is and add a regular pressure switch to the left side in between the 12 and 9 o'clock rails. (which he may well have) That's how I have mine as I don't have the space for the dual switch either.

bkb0000
03-25-10, 18:57
Here's my Colt Law Enforcement 6940
http://i3.photobucket.com/albums/y56/FatalVision555/my%20Guns/100_1144.jpg



i thought the 6940 was a monorail

d90king
03-25-10, 19:13
Here's my Colt Law Enforcement 6940
http://i3.photobucket.com/albums/y56/FatalVision555/my%20Guns/100_1144.jpg


Not a 6940... 6940 is a mono... Nice rifle though.

TwoSqueeze
03-25-10, 19:16
I am working on a build that is almost exactly like this one, when you get a chance let us know how she shoots.

It runs great. The Triple Tap is insanely good at reducing muzzle flip, however I have never tried the PWS FSC unit. I will be putting that on my other build and will have a better idea if the TT was worth the price of admission. This combo with an H Buffer is running really nice but is ejecting to somewhere around the 4, 4:30. I might try a carbine buffer or an H2 buffer to see what they do.

-TS

RetreatHell
03-25-10, 19:27
When the vid was taken, I hadn't messed around with pad location much and before I left the house, since I was already running 2 hours late, I just stuck one of the velcro strips on the side of the PEQ and ran the pad there, which was NOT optimal, especially in the dark when you can't see and are going by touch. The next day I messed around with it and tried to wedge it in between the 9 and 12 o'clock rails, but it just wouldn't fit. I don't know if I was just not applying enough pressure to it to shove it in there, or if my URX rail and XTM panels combo doesn't allow it to fit in there like the KAC panels do that I saw in your previous pics a while back.

I'm considering the dual pressure pad, but would like to try and make this work first. If I did get the dual pad, I'd simply move the T-1 back a notch or two to make room, because I'm not going to move the PEQ-15 forward and make it more front heavy than it already is with the suppressor attached, which isn't so bad as of now, although I do get your point.

ETA: I can wedge the pad in there when the SR07 switch is removed from the 12 o'clock rail, but not when it's attached.

http://i685.photobucket.com/albums/vv219/RetreatHell/BCM%20SBR/BCM%20Middy%20SBR/IMG_3112.jpg

Semper Fi,

-Paul

Titleist
03-25-10, 21:32
hah, on the SR-25 there's tons of room to spare:

http://farm5.static.flickr.com/4044/4452233572_1415451903_b.jpg

Whootsinator
03-25-10, 21:40
My God that's sexy. I want to do dirty things to your rifle.

RetreatHell
03-25-10, 21:43
hah, on the SR-25 there's tons of room to spare:

****in' showoff;)

It looks like the same size as the SR07. Is it a little bigger?

Titleist
03-25-10, 22:01
I do what I can, Paul.

I don't know as I don't have the SR07 to compare it to, but from the looks it may be a slot or so bigger. I know it's a TIGHT fit on the KAC URX. On the SR-25 URX it's got a ton of room.

Microwvbleturtle
03-25-10, 23:18
Titleist,

Where were you able to find the dual switch? I've been looking for one for a while now. I've also been looking for Insight's to run my issued M3X and PEQ but haven't had any luck.

Titleist
03-26-10, 00:12
You can order them direct from Surefire.

RetreatHell
03-26-10, 00:19
Hey Titleist, how 'bout you post a pic since you're at the top. Just sayin';)

http://i685.photobucket.com/albums/vv219/RetreatHell/BCM%20SBR/BCM%20Middy%20SBR/IMG_3097.jpg

Semper Fi,

-Paul

Titleist
03-26-10, 00:22
Uh, you sure you want to call me out?

All right, you asked for it:

http://farm5.static.flickr.com/4056/4395885026_42bed617b6_b.jpg

Stickman
03-26-10, 00:32
Uh, you sure you want to call me out?

All right, you asked for it:





No slacker, he means update the thread so the first thing people see is an image instead of words.... :p

aftermath686
03-26-10, 00:42
Hey Titleist how do you activate the light on the SR15 in the middle.:p


Had to jump on the dog pile!:D

Jer
03-26-10, 01:00
I do what I can, Paul.

I don't know as I don't have the SR07 to compare it to, but from the looks it may be a slot or so bigger. I know it's a TIGHT fit on the KAC URX. On the SR-25 URX it's got a ton of room.

I run an SR07 and based on your pics it looks like yours is about an inch or so longer than an SR07. That is unless they take the same overall length and split it in half for the two switches on yours. If you really want to know post the overall length of yours and I'll post the length of mine. (that sounds bad) :cool:

http://lh5.ggpht.com/_u5gGqJHjM6Q/S49WlYT0cwI/AAAAAAAAAQo/E6Z-0FJaFQQ/s800/2010-03-03%2015.37.18.jpg

m98evolution
03-26-10, 01:09
Hey Titleist,

Now that you've been using the KAC Aimpoint mount, how do you like it compared to the LaRue mount? Is the weight the same?

Thanks again!

aftermath686
03-26-10, 01:26
I run an SR07 and based on your pics it looks like yours is about an inch or so longer than an SR07. That is unless they take the same overall length and split it in half for the two switches on yours. If you really want to know post the overall length of yours and I'll post the length of mine. (that sounds bad) :cool:



Nice stick! The length of the body of the SRxx-D-IT is 3.5 inches. What is the length of the SR07? I am pretty sure there isn't much difference, if any at all.

Jer
03-26-10, 01:33
Nice stick! The length of the body of the SRxx-D-IT is 3.5 inches. What is the length of the SR07? I am pretty sure there isn't much difference, if any at all.

Thanks. I measured my SR07 and it's 3.25" for the switch part itself, not counting any part of the cord including the base that sticks out from the switch. Just the flat part that connects to the rail itself.

aftermath686
03-26-10, 01:52
Roger, I did the same. Guess its about a quarter inch longer. Thanks for the info!

Titleist
03-26-10, 08:19
No slacker, he means update the thread so the first thing people see is an image instead of words.... :p

I suck. I'm sorry. :(


Hey Titleist how do you activate the light on the SR15 in the middle.:p

That's an out of date photo, both the SR-15 and SR-25 have their own dual pads now.


If you really want to know post the overall length of yours...

Wow, that sounded fruity! But Aftermath got the overall dimensions of that pad right. I do wish the dual pad had a constant on, but that's what happens when you rob peter to pay paul.


Hey Titleist,

Now that you've been using the KAC Aimpoint mount, how do you like it compared to the LaRue mount? Is the weight the same?

Thanks again!

I like in that it's not marring like the Larue. That said there's some stuff i dislike about it. I wish the spacers were aluminum and locked in a bit more uniformly, so that the optic didn't have as much side to side play if you have to make a change on the spacer(s). I also find the locking arm's retention system to be less secure a design than the Larue's system, so it's a give and a take.

I run the KAC's because they're a bit lighter, and on my SR-15 the slight cantilevered design gives me just enough room to access the battery compartment on my PEQ-15.

newyork
03-26-10, 14:05
Titleist, Rusted Ace and Retreat Hell, I hate you all ! JK. Great guns guys. I need 2 more jobs.

parishioner
03-26-10, 14:05
http://farm5.static.flickr.com/4056/4395885026_42bed617b6_b.jpg

I believe you could feed a small country with the amount invested in all that hardware......but this is way cooler.

Nice picture.

tylerw02
03-26-10, 14:06
Not a 6940... 6940 is a mono... Nice rifle though.
Exactly what I was thinking.

Titleist
03-26-10, 14:54
I believe you could feed a small country with the amount invested in all that hardware......but this is way cooler.

Nice picture.

Yeah man, it's why I drive a beat up 2001 VW Golf (ironic since my user name is Titleist, I know).

parishioner
03-26-10, 15:05
Yeah man, it's why I drive a beat up 2001 VW Golf (ironic since my user name is Titleist, I know).

You gotta do what you gotta do.

Do you have a PEQ15 to mount to the hood of your Golf? :D

Mega
03-26-10, 17:04
I wanted a PEQ15 for my carbine until I saw the price.
Holy moley... $1750 !!

So I compromised and bought a LaserLyte K15 for $250.
http://www.laserlyte.com/New_Products/New_K-15.html
I think it will do what I need it for.

Titleist
03-26-10, 17:35
K15 is nice, but not in the same league as the PEQ-15 for night work.

I considered helmet mounting my PEQ-15, but I figured that was too silly. :D

mdguy90
03-26-10, 17:42
Is there a link to these ones for $1750? I thought about getting one, but I was under the impression that they were considerably more

pic thread
http://i155.photobucket.com/albums/s297/bigg089/IMG_0173.jpg

Titleist
03-26-10, 17:43
Considerably more, MSRP is 1350. However they require hoop jumping, hoops lit on fire, surrounded by attack dogs, who juggle chainsaws, that shoot electric bolts of hate.

Or you can pay 4000+ dollars on ebay for a fenced version. :rolleyes:

Mega
03-26-10, 18:05
K15 is nice, but not in the same league as the PEQ-15 for night work.


I agree... but I'm not working at night, so my needs were less intense. ;)

Mega
03-26-10, 18:11
Is there a link to these ones for $1750? I thought about getting one, but I was under the impression that they were considerably more


Here is one for a little over $1700
http://www.auroratactical.com/product.php?productid=16423

Titleist
03-26-10, 18:37
Gotta love the fine print:


**LAW ENFORCEMENT/MILITARY ONLY
This item must be sold to a LE or Mil customer only, as required by regulation. If an order is placed that does not meet this specification, the order will be cancelled. Thank you for your interest.

These units, LDI and Insight units, have to be ordered on departmental purchase requests. The FDA closed a lot of the loopholes of officer private purchases a few years back.

Mega
03-26-10, 18:43
These units, LDI and Insight units, have to be ordered on departmental purchase requests. The FDA closed a lot of the loopholes of officer private purchases a few years back.

Well then... I guess us hose beaters don't 'qualify'. :D

MookNW
03-26-10, 18:49
some new goodies
http://img708.imageshack.us/img708/2176/gun004.jpg

Titleist
03-26-10, 19:02
Well then... I guess us hose beaters don't 'qualify'. :D

Unless you know a guy, who knows a guy, who something something something.

Mega
03-26-10, 19:31
Unless you know a guy, who knows a guy, who something something something.

Well yea... I do, I do, I do... but I'm gonna be happy with what I have (for now).
$250 beats $1700 for the purposes that I'm gonna use it for. :D

Titleist
03-26-10, 19:33
If you're not shooting in low or no-light situations, then the K-15 will do a great job.

Okay, sorry to be so chatty and not as photo snappy.

Microwvbleturtle
03-27-10, 00:17
What about us MIL guys? I've had a love affair of PEQ-15s since I first locked eyes on one. In fact, here she is:

http://img.photobucket.com/albums/v160/Marinesniper55/DSCN2728.jpg

Rohardi
03-27-10, 07:08
What about us MIL guys? I've had a love affair of PEQ-15s since I first locked eyes on one. In fact, here she is:

http://img.photobucket.com/albums/v160/Marinesniper55/DSCN2728.jpg

How does the RDS on top of the ACOG work for you? Did you deploy with that setup?

Microwvbleturtle
03-27-10, 10:20
How does the RDS on top of the ACOG work for you? Did you deploy with that setup?

I did deploy with it. Initially I didn't like the location of it and didn't want it. Once I got somewhat used to it I didn't mind it much. It definitely takes some getting used to though.

MeatPuppet
03-27-10, 16:21
New to the AR world, Stag 2L and some furniture.

high plain drifter
03-27-10, 19:35
is that a burris optic meat puppet? if so how do you like it?

Titleist
03-27-10, 19:57
http://farm3.static.flickr.com/2797/4467859523_196e516bb0_b.jpg

TOMTOM
03-27-10, 20:04
Blackberry camera = horrible.

http://i737.photobucket.com/albums/xx14/TD236/IMG00018.jpg

aftermath686
03-27-10, 20:58
I really like that setup Titleist! Looking very clean.

Edit:: What height is your KAC T1 mount? HK height?

EDIT again:: Is that a newer finish on the SF scout lights? Looks great. haha I can't stop looking at your picture.

MeatPuppet
03-27-10, 21:28
is that a burris optic meat puppet? if so how do you like it?

It is actually an NcStar red/green dot. 4 different rectiles in both colors. Love it for what it is, a $40 device. I am planning on getting a better scope at the next gun show.

Titleist
03-27-10, 21:31
I really like that setup Titleist! Looking very clean.

Edit:: What height is your KAC T1 mount? HK height?

EDIT again:: Is that a newer finish on the SF scout lights? Looks great. haha I can't stop looking at your picture.

Thanks, it's basically evolved over the last year in to this setup. The KAC mount you see is the full height mount, so lower 1/3rd co-witness.

Not sure about the finish, mine was a little un-even on the surface, it'll get scratched up soon enough. :P

Stickman
03-27-10, 22:20
BCM 14.5" w/extended A2 FS.



http://stickman.rainierarms.com/galleries/BCM/STCK0775-1024-Stick.jpg

texas12
03-28-10, 00:23
http://farm3.static.flickr.com/2797/4467859523_196e516bb0_b.jpg
Titleist is that a recent production surefire M600C? The color looks for flat tan then shinny gold like the one I picked up a couple months ago.

Titleist
03-28-10, 00:37
It's still got some gold flake to it, but it's more tan than anything. To be honest I found the surface finish to be kind of patchy in areas.

My M300 mini-scout also has the same flatter surface finish:

http://farm3.static.flickr.com/2787/4456530900_8d7975b84a_b.jpg

texas12
03-28-10, 00:50
It's still got some gold flake to it, but it's more tan than anything. To be honest I found the surface finish to be kind of patchy in areas.

My M300 mini-scout also has the same flatter surface finish:

http://farm3.static.flickr.com/2787/4456530900_8d7975b84a_b.jpg

That might just give me an excuse to buy a tan mini scout and turn another black gun tan.

Im lovin your sr-15 i dont think you could make it any better, but knowing you you'll find a way ;)

Titleist
03-28-10, 00:53
As far as I'm concerned that gun is done...well until I can get my hands on one of those new Surefire's with the TIR/Vampire heads.

But the SR-15 really is my work horse rifle, close to 11k rounds through it. I just love that thing.

Bowser
03-28-10, 01:01
BCM 14.5" w/extended A2 FS.



[IMG]http://stickman.rainierarms.com/galleries/BCM/STCK0775-1024-Stick.jpg[IMG]

You have any full rifle pics of this with the RIS II? Looks good.

texas12
03-28-10, 01:02
As far as I'm concerned that gun is done...well until I can get my hands on one of those new Surefire's with the TIR/Vampire heads.

But the SR-15 really is my work horse rifle, close to 11k rounds through it. I just love that thing.



I had a chance to mess with one a few weeks back and the 95mW IR output was nice but the LED was definitely lacking. I guess its a trade off for having the ability to switch from Vis to IR

MValdez17
03-28-10, 01:41
S&W M&P15T
4607

4608

hkhunter
03-28-10, 15:11
Titleist,

did you cut the forks off the ASAP to make it work with the SR-15 or is that a new ASAP design?



http://farm3.static.flickr.com/2797/4467859523_196e516bb0_b.jpg

Titleist
03-28-10, 16:40
Titleist,

did you cut the forks off the ASAP to make it work with the SR-15 or is that a new ASAP design?

I ground the 'wings' off and re-parkerized the plate. Paul (RetreatHell) has one of the ASAPs I made as well.

AMMOTECH
03-28-10, 16:54
***EDIT****

Belmont31R
03-28-10, 17:00
http://i274.photobucket.com/albums/jj245/BM31R/SR15-1.jpg

Titleist
03-28-10, 17:05
Belmont, didn't you get the memo?


Only 1x Knights SR-15 E3 IWS may be posted within 24 hours that includes a pelican case, and/or magpul vinyl sticker.

:p Very nice, sir.

Quiet-Matt
03-28-10, 17:20
http://lh6.ggpht.com/_5kA3JwNkBxc/S6-qwYAFnOI/AAAAAAAAFN8/Sb3HUY7d6b8/s720/DSC00826.JPG

RetreatHell
03-28-10, 17:53
I ground the 'wings' off and re-parkerized the plate. Paul (RetreatHell) has one of the ASAPs I made as well.

And you did a damn fine job with it!

http://i685.photobucket.com/albums/vv219/RetreatHell/Magpul%20AFG/IMG_2971.jpg

Semper Fi,

-Paul

hkhunter
03-28-10, 19:37
thanks! it looks like I've got a new project for this week


I ground the 'wings' off and re-parkerized the plate. Paul (RetreatHell) has one of the ASAPs I made as well.

Titleist
03-28-10, 20:02
And you did a damn fine job with it!
-Paul

Thanks, Paul, your bribe check will be in the mail tomorrow. ;)

Bowser
03-29-10, 02:08
deleted

RetreatHell
03-29-10, 02:42
deleted

Don't know why you deleted it, man. The MW2 effects made me laugh!:p

ForTehNguyen
03-29-10, 09:27
weight?? that was the point of the build, afterall, right?

I have a postal scale coming in. I estimated on paper for the rifle to weigh around 5.5 lbs. When the scale comes in this week, we will see how much it really weighs. It would be lighter if I got a 14.5" carbine vs 16 middy, but I want to stick with 16s. 16" carbine lightweight would be slightly lighter than 16 middy too, but I prefer middys.

Not the lightest I can get of course, had to balance it out with personal preferences.

Stickman
03-29-10, 09:45
http://www.flickr.com/photos/stickgunner/4471118973/

http://farm5.static.flickr.com/4004/4471118973_cb884f2bf4_o.jpg

lethal dose
03-29-10, 09:55
the tt shemagh is certainly a nice touch.

texas12
03-29-10, 17:45
http://img338.imageshack.us/img338/2102/dscn0713i.jpg
http://img18.imageshack.us/img18/51/dscn0712l.jpg

enopty27
03-29-10, 18:29
BCM 16" MIDDY
BCM Lower
BCM BCG
Gunfighter MOD 4 Charging Handle
VLTOR compensator
TROY 9" Handrails
Surefire G2L
Magpul AFG
Stark Pistol Grip
Magpul CTR Stock
TROY BUIS
EoTech XPS 2-0 w/ GG&G lens cover

https://www.m4carbine.net/attachment.php?attachmentid=4616&d=1269905309
https://www.m4carbine.net/attachment.php?attachmentid=4617&d=1269905215
https://www.m4carbine.net/attachment.php?attachmentid=4618&d=1269905355

Cincinnatus
03-29-10, 18:42
Gotta love the fine print:



These units, LDI and Insight units, have to be ordered on departmental purchase requests. The FDA closed a lot of the loopholes of officer private purchases a few years back.

The FDA? WTF? They now classify a PEQ as food or drugs???!!!!

hossb7
03-29-10, 19:09
The FDA? WTF? They now classify a PEQ as food or drugs???!!!!

Infra-red is regulated by the FDA.

Cincinnatus
03-29-10, 19:16
Infra-red is regulated by the FDA.

Thanks, I didn't know that. Are they also responsible for making the Aimpoint CEU unavailable to civilians or is that just an Aimpoint policy and not an actual legal regulation?

Belmont31R
03-29-10, 19:21
http://i274.photobucket.com/albums/jj245/BM31R/DSC_0825.jpg

http://i274.photobucket.com/albums/jj245/BM31R/DSC_0832.jpg

http://i274.photobucket.com/albums/jj245/BM31R/DSC_0837.jpg

http://i274.photobucket.com/albums/jj245/BM31R/DSC_0841.jpg

Bowser
03-29-10, 20:00
[IMG]http://i274.photobucket.com/albums/jj245/BM31R/DSC_0825.jpg[IMG]

Nice!

TOMTOM
03-29-10, 20:05
http://i737.photobucket.com/albums/xx14/TD236/HPIM1302.jpg

Belmont31R
03-29-10, 20:14
Nice!




Thanks :cool:


http://i274.photobucket.com/albums/jj245/BM31R/DSC_0846.jpg

http://i274.photobucket.com/albums/jj245/BM31R/DSC_0848.jpg

jparish62
03-29-10, 20:30
So, I've been looking at the rifles on here and have noticed that a lot of them are sporting peq-15's. I was just wondering how you all got your hands on them

Bowser
03-29-10, 20:30
The RIS II FSP looks real good, first pics of the latest version of it I've seen clearly of one installed. I've been thinking hard about getting a black RIS II FSP for my upper.

jparish62
03-29-10, 20:46
http://i193.photobucket.com/albums/z152/eternal24k/044.jpg

Is that a select fire lower? If it is I am hella jealous!

JBecker 72
03-29-10, 21:48
Is that a select fire lower? If it is I am hella jealous!

no.
if it was it would have the pin above the selector.

RetreatHell
03-29-10, 22:51
Thanks, I didn't know that. Are they also responsible for making the Aimpoint CEU unavailable to civilians or is that just an Aimpoint policy and not an actual legal regulation?

Negative. As per Leroy Thompson's article in SWAT Mag this month (actually the May 2010 issue), where he "reviews" the CEU, Aimpoint is personally choosing to limit sales of the CEU to LEO and .Mil customers only at this time.

Semper Fi,

-Paul

ras61541
03-29-10, 23:09
http://i746.photobucket.com/albums/xx104/ras61541/Armalite/CIMG7680.jpg?t=1269921605
http://i746.photobucket.com/albums/xx104/ras61541/Armalite/CIMG7681.jpg?t=1269921503

USMC88-93
03-29-10, 23:54
Want to upgrade some of them but right now this is what I have. (I need some optics).
http://img.photobucket.com/albums/v651/PhotoTWB/AR-15/6AR2AK.jpg
http://img.photobucket.com/albums/v651/PhotoTWB/dewalt.jpg

Stickman
03-30-10, 00:42
the tt shemagh is certainly a nice touch.


Thanks, they have them in three colors now.

Stickman
03-30-10, 00:46
Board code is acting up again.....

Stickman
03-30-10, 00:48
You have any full rifle pics of this with the RIS II? Looks good.


http://stickman.rainierarms.com/galleries/BCM/STCK0601-1024-Stick.jpg



http://stickman.rainierarms.com/galleries/BCM/STCK0599-1024-Stick.jpg

jparish62
03-30-10, 06:43
no.
if it was it would have the pin above the selector.

ok, that's what i thought, but figured I'd ask since the body has the designation for it next to your selector

JBecker 72
03-30-10, 13:13
http://i149.photobucket.com/albums/s73/hownowbrowncow_02/Guns/surefire002.jpg

jacobswel
03-30-10, 16:54
TOP: Wilson Combat
BOTTOM: Colt 6940
http://i478.photobucket.com/albums/rr145/jacobswell26/IMG_0677.jpg

Belmont31R
03-30-10, 18:00
http://i274.photobucket.com/albums/jj245/BM31R/DSC_0863.jpg

UVvis
03-30-10, 19:20
http://i137.photobucket.com/albums/q223/db556/mpowa.jpg
Sabre (2MOA ML3, Larue rail, Surefire G2 in a Viking's Mount, Magpul furniture)
BCM/Stag (2MOA ML3, Larue Rail, Surefire G2 in a Viking's Mount, Magpul furniture)
BCM (everything with CavArms hand guard)
BCM (just like the one above it)

The BCM/Stag and Sabre guns both started around 2006. After trying several different configurations, this is what I ended up with. There honestly isn't anything on these two that I would change at current. The ML3's with the 2MOA work great with a magnifier, The XTM panels allow me to add a bipod quickly if I want to shoot like that. Slings pop on the QD points. Tada!

The bottom two guns represent what I'd consider an ideal out of the box set up.

Seth Gecko
03-30-10, 21:05
Added some Magpul accessories to my KAC SR-15. :D

http://farm5.static.flickr.com/4040/4477923326_39090ddac3_o.jpg

SKULL1
03-30-10, 21:27
http://img.photobucket.com/albums/v254/ehrljohn/osc312.jpg

SKULL1
03-30-10, 21:30
http://img.photobucket.com/albums/v254/ehrljohn/osc298.jpg

SKULL1
03-30-10, 22:02
http://img.photobucket.com/albums/v254/ehrljohn/rangeday002.jpg

SKULL1
03-30-10, 22:03
http://img.photobucket.com/albums/v254/ehrljohn/osc313.jpg
http://img.photobucket.com/albums/v254/ehrljohn/osc314.jpg


14.5 Noveske Afghan
Larue Billet Lower
Surefire X300
Aimpoint T1
Vltor Emod
Magpul MIAD
Magpul AFG
Troy Larue BUIS
Magpul Emag 10/30
Magpul BAD

earthworm94
03-31-10, 11:37
Here is my (now purportedly defunct) ADS Alpha Basic ordered right on the night Obama is elected. Changes include a BFG VCAS Padded sling, Magpul MIAD grip, and a used Aimpoint M2 with a LaRue LT-150 mount. Not particularly accurate (about 3 MOA from 100yds), but it never skips a beat beside one magazine related failure chambering Wolf steel case ammo.

Now, I'm waiting for the Magpul plastic rails, MOE handguard and a saving up for a Streamlight TLR-1s and I'll have the perfect home defense rifle!

Pics are up, enjoy!

http://lh6.ggpht.com/_QJ5lPaLXguA/S7N1I-S_X6I/AAAAAAAAFqA/Zldkb4QtBPI/s800/DSC_5658.JPG

http://lh4.ggpht.com/_QJ5lPaLXguA/S7N1JAd4yPI/AAAAAAAAFqE/q20tzqHWyPw/s800/DSC_5665.JPG

http://lh6.ggpht.com/_QJ5lPaLXguA/S7N1Jl8Yf5I/AAAAAAAAFqM/3dKab0T8Yvg/s800/DSC_5670.JPG

http://lh3.ggpht.com/_QJ5lPaLXguA/S7N1KEZ_NUI/AAAAAAAAFqQ/alMLAYaj-6I/s800/DSC_5679.JPG

http://lh6.ggpht.com/_QJ5lPaLXguA/S7N1Ki80-PI/AAAAAAAAFqU/4Be0tmGOuIA/s800/DSC_5684.JPG

http://lh6.ggpht.com/_QJ5lPaLXguA/S7N1LCGubKI/AAAAAAAAFqY/3TtYPlU-B9k/s800/DSC_5699.JPG

http://lh6.ggpht.com/_QJ5lPaLXguA/S7N1Ls4wBPI/AAAAAAAAFqc/Tmi6mNZGrp8/s800/DSC_5703.JPG

http://lh6.ggpht.com/_QJ5lPaLXguA/S7N1L0FzB3I/AAAAAAAAFqg/GxpgaukGqeU/s800/DSC_5704.JPG

http://lh3.ggpht.com/_QJ5lPaLXguA/S7N1MgYFicI/AAAAAAAAFqo/IAy-2EK39xk/s800/DSC_5749.JPG

http://lh4.ggpht.com/_QJ5lPaLXguA/S7N1NNds_bI/AAAAAAAAFqs/g0uinZLye1g/s800/DSC_5764.JPG

http://lh4.ggpht.com/_QJ5lPaLXguA/S7N1MeO_ukI/AAAAAAAAFqk/YSsLcJw30co/s800/DSC_5713.JPG

Here is a target from 100 yds:
http://lh4.ggpht.com/_QJ5lPaLXguA/S7JugEeVTUI/AAAAAAAAFog/H3TKLww9OB4/s800/image0.jpg

50 yds:
http://lh6.ggpht.com/_QJ5lPaLXguA/S7JuhCP_2hI/AAAAAAAAFok/lF5_1AHmMd0/s800/image1.jpg

LMarshall73
03-31-10, 13:15
Was playing with camera settings earlier:

http://farm3.static.flickr.com/2782/4479610962_a9fced6cb5_o.jpg

http://farm3.static.flickr.com/2790/4478984267_28f8ffa721_o.jpg

http://farm5.static.flickr.com/4061/4478984139_e6c114da59_o.jpg

http://farm3.static.flickr.com/2776/4478984049_db017403e9_o.jpg

http://farm5.static.flickr.com/4003/4479694638_405e43abcc_o.jpg

http://farm3.static.flickr.com/2784/4479068327_a06e96dfa6_o.jpg

Belmont31R
03-31-10, 16:08
http://i274.photobucket.com/albums/jj245/BM31R/DSC_0913.jpg

http://i274.photobucket.com/albums/jj245/BM31R/DSC_0915.jpg

http://i274.photobucket.com/albums/jj245/BM31R/DSC_0916.jpg

earthworm94
03-31-10, 16:51
Since I have people PM me about the targets I used for zeroing, I'll post the links here:

Zeroing targets for red dot sights at standard sight height (2.6")

25 yds zeroing target for 50 yds zero

http://www.scribd.com/doc/7998596/Red-Dot-Target-25-Yards

50 yds zeroing target for 50 yds zero

http://www.scribd.com/doc/7998597/Red-Dot-Target-50-Yards

Daemonbane
03-31-10, 22:29
Mine rifle has gone through some changes :), just got to make time to trek out to my 'local' rifle range...

http://farm3.static.flickr.com/2754/4480212725_297a6981fb_b.jpg

Cousin gave me his old M4 handguard to try and I got some bolt on MI rails & grip when I ordered the BCM upper.

TOMTOM
04-01-10, 11:04
http://i737.photobucket.com/albums/xx14/TD236/HPIM1301-1.jpg

djegators
04-01-10, 14:41
Pretty much finished with this one, other than deciding on the AFG, and possibly adjusting the rail covers.

Noveske N4 Recce Low-Pro
Magpul UBR
Magpul AFG
Magpul XM and ladder rail covers
ACOG TA33R-8 in Larue QD mount


http://i44.tinypic.com/2yl2oie.jpg


http://i44.tinypic.com/20jk6zb.jpg

Rusty_Shackleford
04-01-10, 14:54
http://i555.photobucket.com/albums/jj475/Cansler_Tactical/CanslerTacticaljpg1.jpg

Caeser25
04-01-10, 18:57
Was playing with camera settings earlier:


http://farm3.static.flickr.com/2776/4478984049_db017403e9_o.jpg





is this a 9 or 10?

Seagrave7
04-01-10, 20:25
is this a 9 or 10?

I would say thats a 9. Mine is a 10.

http://i301.photobucket.com/albums/nn60/Seagrave77/IMG_4811.jpg

Daemonbane
04-01-10, 22:29
Got a picture request if anyone able to: Mid-length with a front sight tower, a vltor casv-m, and a AAC Blackout MITER mount.

Stickman
04-01-10, 23:53
BCM upper/ Noveske Lower


http://stickman.rainierarms.com/galleries/BCM/STCK0902-1024-Stick.jpg

Showbart
04-02-10, 08:06
First rifle after getting back into ARs. BCM complete middy upper 14.5" with AAC Blackout. On a YHM complete lower, the quality of which is pleasantly suprising. 3 more complete rifles are in the plan for the future and at least 1 more upper. Don't have any real use for alot of rails but will get one or two, a 6940 for sure and maybe a VTAC (XTR? the LW one?). Will be one 6.8 middy in the mix too, likely complete DD. Most everything else will be Colt from now on, as it was in the past.

http://i213.photobucket.com/albums/cc296/Showbart/AR/BCM.jpg

LMarshall73
04-02-10, 12:31
is this a 9 or 10?

It is a 9

jdavis6576
04-02-10, 17:36
http://i706.photobucket.com/albums/ww65/jdavis6576/IMG_3083.jpg

http://i706.photobucket.com/albums/ww65/jdavis6576/IMG_3085.jpg

Merle
04-03-10, 12:49
My latest build.

http://i192.photobucket.com/albums/z198/merlebrooks/003-4.jpg

armakraut
04-03-10, 13:30
My latest build.

14.5?

Mega
04-03-10, 14:28
Been updating my CQB carbine this winter.
There are very few Bushmaster parts left.
Upper. lower, and the barrel are all that is left. Everything else has been replaced.

The barrel will be replaced once the Form 1 clears. She will get a 12.5" barrel and become a CQB SBR.

BCG is by BCM. Stock is a Magpul CTR, grip is a MIAD, sights are MBUS, forward grip is an AFG, Magpul BAD and Magpul rail covers.
Laser is a K-15 LaserLyte green laser, and the flash suppressor is a Noveske KX3 'Flaming Pig'.

http://www.mdshooters.com/gallery/files/4/4/4/1/dscn0062.jpg

http://www.mdshooters.com/gallery/files/4/4/4/1/dscn0065.jpg

http://www.mdshooters.com/gallery/files/4/4/4/1/dscn0066.jpg

http://www.mdshooters.com/gallery/files/4/4/4/1/dscn0078.jpg

http://www.mdshooters.com/gallery/files/4/4/4/1/dscn0072.jpg

http://www.mdshooters.com/gallery/files/4/4/4/1/dscn0076.jpg

texag
04-03-10, 15:39
My DDM4 as it sits now:
http://i785.photobucket.com/albums/yy138/TexAg10/Firearms/SANY0226.jpg

What it will look like when I SBR it, hopefully by the end of 2010:
http://i785.photobucket.com/albums/yy138/TexAg10/Firearms/SANY0226-1.jpg

snailfan
04-03-10, 17:13
http://img.photobucket.com/albums/v147/snailfan/DSC_0039copy4.jpg

jparish62
04-03-10, 17:51
My latest build.

http://i192.photobucket.com/albums/z198/merlebrooks/003-4.jpg

What rail system is that?

RetreatHell
04-03-10, 17:54
What rail system is that?

That's the Daniel Defense OmegaX 12.0 FSP rail. Great rail!

3p031
04-03-10, 18:15
I have been looking at that rail for a long time now. Think I might get one but could you tell me how it mounts to the upper? I cant find pics on how it does.
Im used to the Larue mount so I hope its as sturdy as that.

Quiet-Matt
04-03-10, 19:12
I have been looking at that rail for a long time now. Think I might get one but could you tell me how it mounts to the upper? I cant find pics on how it does.
Im used to the Larue mount so I hope its as sturdy as that.

The two halves slip over a propriatory barrel nut and held tight by 4 set screws. The two halves are held together by 6 screws. Solid rail.
http://lh3.ggpht.com/_5kA3JwNkBxc/S7egAKsrJAI/AAAAAAAAFTY/eGccsuSUniI/s800/Christmas%20265.jpg

JBecker 72
04-03-10, 20:34
yes it is a solid rail.
I love mine.

Merle
04-03-10, 22:59
14.5?

Yea, it's a Colt M4 barrel with a pinned extended A2 flash hider.

ghostman1960
04-04-10, 02:50
http://i596.photobucket.com/albums/tt45/ghostman1960/007-1.jpg

Stickman
04-04-10, 11:22
Happy Easter to all!


http://stickman.rainierarms.com/galleries/Noveske/IMG_1697%201028%20Stick%201.jpg

Titleist
04-04-10, 11:29
Bravo, stick! well played!

TOMTOM
04-04-10, 11:35
great picture Stick!

pic thread:

http://i737.photobucket.com/albums/xx14/TD236/HPIM1309.jpg

SKULL1
04-04-10, 12:05
awesome pix.. stick..