Range Report: Hornady 5.56mm 75 Grain TAP SBR

It looks to me like the "black" ammo is the same stuff, just packaged differently. It shows the exact same velocity from the 11.5 inch test barrel. I would like to know what Hornady says about that.

I just spoke to a tech at Hornady who confirmed that the TAP SBR 75 gr load it is identical to the 75 gr Black load. Only the packaging is different.

Quote:

---

Originally Posted by Rayrevolver

Devils Advocate: I am hoping the SBR load bullet is specifically designed to expand at lower working velocities. And maybe they chose the powder so that blast and concussion would be less with this load. Dunno.

If you look at their "Black" SBR ammo, they claim 2321 fps with an 11.5" barrel. I wonder if during development of the above SBR load, they realized they can market it to suppressor folks since it was less blast.

I kinda want to try the Black SBR suppressed 5.56 and see if I can notice a difference in sound. Probably not.

---

I don't think it will. For that, you need a copper bullet (TSX/GMX). These bullets turn a 10.5 into 150yds gun.


C4

Thanks for the review!

More data:

DD 10.75" (chopped) 2226fps, 1.7" 10-shot @ 100 yds, T-1

This ammo does seem quiet (suppressed) compared to BH or IMI 77 OTM, although it gives up 150-220fps depending on the particular barrel. (10.5-11.5" that I tested)

For comparison (all velocities are with M4SDII):

DD 10.75" --- 75 TAP SBR 2226, 75 Gold Dot 2183, 77 IMI 2391 64 Gold Dot 2287 62 Mk318 2604

Sionics 11.5" -75 TAP SBR 2244, 75 Gold Dot 2273, 77 IMI 2456 64 Gold Dot 2479 62 Mk318 2741


So, yes, the 75 GDs are a bit faster in my tests than the 75 TAP SBR. Still almost 100fps slower than the referenced test.

Quote:

---

Originally Posted by vicious_cb

Interesting, Andrew was getting higher velocity out his 11.5" SBR with 75gr Gold Dot. You would think an SBR specific load would yield higher velocity than its competitor out of, well, an SBR. Speer 75 gr Gold Dot isn't even advertised as an SBR specific load.

Speer 75 gr Gold Dot

https://youtu.be/2lkI36eUoy4

11.5" SBR:
Velocity: 2,370 fps
Penetration: 19.5"
Retained weight: 73.0 gr
Max expansion: 0.563"
Min expansion: 0.305"



20" Rifle:
Velocity: 2,774 fps
Penetration: 15.2"
Retained weight: 66.2 gr
Max expansion: 0.686"
Min expansion: 0.382"


SBR Windshield:
Velocity: 2,328 fps
Penetration: 22" (approx.)
Retained weight: 60.9 gr
Max expansion: 0.426"
Min expansion: 0.246"

---

Quote:

---

Originally Posted by MQ105

For comparison (all velocities are with M4SDII):

DD 10.75" --- 75 TAP SBR 2226, 75 Gold Dot 2183, 77 IMI 2391 64 Gold Dot 2287 62 Mk318 2604

Sionics 11.5" -75 TAP SBR 2244, 75 Gold Dot 2273, 77 IMI 2456 64 Gold Dot 2479 62 Mk318 2741


So, yes, the 75 GDs are a bit faster in my tests than the 75 TAP SBR. Still almost 100fps slower than the referenced test.

---

I'm assuming you have the standard Sionics 11.5" barrel, and not the reduced gas port one correct?

Thanks

Quote:

---

Originally Posted by w3453l

I'm assuming you have the standard Sionics 11.5" barrel, and not the reduced gas port one correct?

Thanks

---

I have the reduced port barrel, and have also installed a homemade gas block port reduction insert that is .0630". It's pretty good with the M4SDII and will cycle Wolf Gold.
Without the suppressor:
it locks back 100% when clean and/or freshly lubed. When dirty and without recent lube it cycles 100% but won't reliably lock back. With M193, M855, Mk262, Mk 318 it is 100% whether dirty, clean, whatever, and locks back.

Quote:

---

Originally Posted by MQ105

I have the reduced port barrel, and have also installed a homemade gas block port reduction insert that is .0630". It's pretty good with the M4SDII and will cycle Wolf Gold.
Without the suppressor:
it locks back 100% when clean and/or freshly lubed. When dirty and without recent lube it cycles 100% but won't reliably lock back. With M193, M855, Mk262, Mk 318 it is 100% whether dirty, clean, whatever, and locks back.

---

Thanks!

I have been contemplating on buying the RGP barrel, but I will not be running suppressed. I wasn't sure if that's still a good idea.

The .070 port in the reduced port barrel runs very well non suppressed.