Grant at G&R has the correct barrel for $269. It's a Colt 10.3" barrel. http://www.gandrtactical.com/cgi-bin...on&key=SP64049
It sounds like you are going for the early SF/ODA CQBR (not mk18) clone, so some of the stuff will be different than the original mk18mod0 or CQBR block 1.5/2.
Your lower as a stand in for a 727 lower/M4 lower correct for the time period
Car Stock with Rubber pad zip tied for good measure
H2 or H3 buffer
Standard End Plate
Colt upper, AF marked if possible
Colt 10.3" barrel
Colt or USGI contract BCG
KAC RAS
NT4 Suppressor mount/Suppressor OR BE Meyers 249 Flash hider
PEQ2 or time period correct visible/IR laser
Aimpoint Comp M in QRP mount
or Eotech 511, Eotech 553.
Matech buis
Various lights, the famous pics typically have the Surefire "ganster grip" M900
Also note the block 1.5 PR (phased replacment) with SU231 and later PEQ IR laser
[IMG] [/IMG]
With waffle stock and C MORE sight
PR with BE meyers and ACOG
Last edited by Split66; 09-30-15 at 12:14.
"BRD, much like the Wutang clan, is nothing to f@ck with"
G&R Tactical is good to go for Colt clone build parts. I got my 10.3" Colt barrel from them plus a several Colt LPK's to go with Colt stripped lowers I got off GunBroker. I would also watch GunBroker, sometimes you can find parts slightly cheaper listed on there. I've bought thousands worth of Colt parts over the past 3 years for clone builds.
Thanks Split, that's the direction I am going! So you would you say a cut Colt carry handle would be a no-go?
All of the CAG/ODA/SF/Army CQBRs I've seen in photos have had Matechs or possibly KAC Buis. If you check out Oliver North's book "American Heroes in Special Operations" you can glimpse a few other ODA CQBRs here and there.
"BRD, much like the Wutang clan, is nothing to f@ck with"
Last edited by Ryno12; 10-02-15 at 20:23.
IMG_4868 by splittiebus 66, on Flickr
I based mine around Kyle Defoor's mk18 or an early SEAL mk18 in general. It's all Colt. It has the incorrect suppressor though, no PEQ2, an incorrect FM cover for the Surefire, a RAS instead of a RIS, and no select fire. Well sometimes....
cloned gun
Last edited by Split66; 09-30-15 at 12:46.
"BRD, much like the Wutang clan, is nothing to f@ck with"
Here is a little bit of info.
Upper and lower receivers: The lower receiver is a standard M4A1 lower receiver sometimes modified with the addition of a CQD RSM sling adapter plate. However, many CQBR rifles also use surplus M16A1 lower receivers. Internally, the CQBR also takes advantage of a larger gas port and modified bolt carrier and buffer assembly. The gas port has been opened to 0.070 in (1.8 mm). A number of Lewis Machine & Tool 10.5" (266.7 mm) upper receivers have also been reported to have been purchased for the CQBR program. These upper receivers feature a gas system optimized for short barrel use.
Sights: Initially, detachable carrying handles cut down so that only the rear sight assembly was used. However, most of these have been replaced with the similar, commercially-made Lewis Machine & Tool adjustable rear sight. Also used are several types of reflex and magnified optics, most commonly seen is the Aimpoint CompM2 in a Wilcox Industries Corp. Picatinny (MIL-STD-1913) mount.
"A Bad Day At The Range Is Better Than A Great Day Working"
USMC Force Recon 1978-1984
US Air Force Res. 1995-2004 (Air Transportation)
M16/AR15 shooter since 1978, gun collector and AR builder since 2004
Bookmarks