The Official SBR Picture Thread

[the_1iviper]

[RobertTheTexan]

Is there a selector switch position for “Beast Mode” on that bad boy?

Helluva setup.


Sent from my iPhone using Tapatalk

[0uTkAsT]

[the_1iviper]

Is there a selector switch position for “Beast Mode” on that bad boy?

Helluva setup.


Sent from my iPhone using Tapatalk

thanks man , i have dropped both a binary trigger and an echo trigger in it before to try out



this is with the mod 1 upper but i'm sure the mod 2 upper would run just as smooth

[0uTkAsT]

Had an opportunity to stretch this rifle's legs a little and I'm quite pleased. 18" target, sporadic wind alternating 90-270 degrees, shooting bulk remanufactured 55gr .223 out of a bucket with the 11.5" enhanced lightweight barrel. Top right was a 3-shot group at 200 yards fired fairly quickly, bottom right was three separate 3-shot strings at 500 yards. Did not dial any dope, just used the P4Xi's BDC reticle for holdovers and guessed on windage (range had windsocks at the 100 and 300 yard lines).

[0uTkAsT]

Had an opportunity to stretch this rifle's legs a little and I'm quite pleased. 18" target, sporadic wind alternating 90-270 degrees, shooting bulk remanufactured 55gr .223 out of a bucket with the 11.5" enhanced lightweight barrel. Top right was a 3-shot group at 200 yards fired fairly quickly, bottom right was three separate 3-shot strings at 500 yards. Did not dial any dope, just used the P4Xi's BDC reticle for holdovers and guessed on windage (range had windsocks at the 100 and 300 yard lines).

[RWA007]

[QUOTE=kukworld;2604861]

Cartel, what light model and mount are you using on that SBR?...looks great!

Here's mine. 300blk, AAC upper. I run an Omega on it most of the time.

[/How do you install the vertical grip without the pic rail on urx 3.1?


Sent from my iPhone using Tapatalk

There is a KAK URX kit that comes with the side panels, handstops and picattiny rail pieces. I just bolted one of those piccatinny rail pieces to the bottom of it then used a regular picatinny rail VFG (BCM) with it. I didn't like how the rail piece extended both forward and backward of the grip itself, so I trimmed the rail itself so it looks like the vfg is just attached right to the URX rail itself. Pretty clean. However, it gets HOT just in front of the vfg so I'll likely install another panel piece there just for some insulation.

[MegademiC]

[QUOTE=RWA007;2610312]

There is a KAK URX kit that comes with the side panels, handstops and picattiny rail pieces. I just bolted one of those piccatinny rail pieces to the bottom of it then used a regular picatinny rail VFG (BCM) with it. I didn't like how the rail piece extended both forward and backward of the grip itself, so I trimmed the rail itself so it looks like the vfg is just attached right to the URX rail itself. Pretty clean. However, it gets HOT just in front of the vfg so I'll likely install another panel piece there just for some insulation.

You can attach it directly- made a thread about it a while ago:

https://youtu.be/LQuWnxqCOvs

[Achilles11B]

B8EB899F-7942-4B35-B26E-CB9AD3967A3E.jpg


Nothing fancy, but I’m a fan of keeping it simple. BCM 12.5” Upper on a Spikes lower. Aimpoint PRO, Streamlight TLR-1, and Magpul VFG and that’s it. I’m looking forward to taking some carbine classes this year with it.

[yrch21]

SIONICS 11.5 Reduced Gas Port SBR with Q Trash Panda