I got mine today from Jason at Bigdawg Tactical.
I got mine today from Jason at Bigdawg Tactical.
Semper Fi
Here's my latest build
Specs:
POF Billet Lower
Vltor MUR
Daniel Defense AR15 Lite Rail 10.0
Sadlak LoPro Gas block
Magpul CTR
Tango Down Panels, Battle Grip, and Shorty Grip
KNS Gen II trigger pins
Ambi Selector
I am going to SBR this to 10.5 whenever I get the paperwork approved. I have a KX3 for it already, and I am gonna put an Aimpoint on there as well. Still haven't decided on back up iron sights.
Sweet build Cyclic!
Employee of colonialshooting.com
Not the best pic. but here's a shot of my 6920 with 921 upper. My homage to the US Military. A fairly pedestrian M4 wannabe compared to some of the high end kit seen here but it works for me.
-KAC RIS
-C7 front sight post
-KAC Vert grip
-KAC 300M BUIS
-ACOG TA01NSN
-Colt M16 Carrier
-Vickers Sling
-Gapper
Colt Sporter Target C7A1 Clone. All Colt with C79 Elcan and Diemaco BUIS. Stock gun but it has some nice features seldom seen up here (Canada) like Govt. profile barrel, Mil Spec . front pivot pin, mag fence, bayonet lug and flash hider all in the same early Colt. Flat top is from a 6721 upper without M4 ramps.
Bone Stock Colt 6920. My Form 6 OK gun.
Colt Sporter 2 Carbine. Stock gun save for the jobber CAR stock which I will remedy RFN.
Nobody Cares! Fix It!
PMAGs are in, so I thought I would post a picture.
Here's what Grant built (in stages) for me.
POF P-415 GEN II lower
CMT lower parts kit
POF / Timney trigger
CMT receiver extension, FDE Cerakote
MAG-PUL CTR stock, FDE
MAG-PUL MIAD pistol grip, FDE
Tango Down PR-4 single point sling attachment
VLTOR MUR
FN M16 bolt / bolt carrier group
CMMG SOCOM 16" barrel, chrome-lined, M4 ext., 1/7 twist
YHM Phantom II flash suppressor
Midwest Industries #20 2-piece free-float rail
PRI Gas Buster charging handle
LaRue LT-103 BUIS
Eotech 512
LaRue LT-110 Eotech mount
Bue Force Gear Vickers VTAC 2-point sling, foliage green
barrel, rail, & eotech painted Brownell's Earth Brown Alumahyde II
knife by me, 1/4" ATS-34, Micarta handle
My first build.
Specs:
Lower:
-POF P-415 Gen I Lower
-CMT Lower Parts Kit
-RRA ADCO Enhanced Two-stage Trigger
-Magpul MIAD
-Magpul Enhanced Trigger Guard
-Magpul CTR Stock (H Buffer)
Upper:
-LaRue Stealth with M4 Cuts
-Denny's 16" Operator Barrel
-LaRue 9.0 Handguard
-PRI Gasbuster Charging Handle (Hoping for a supressor one day)
-LMT Bolt Carrier Group
-Troy BUIS
Fired 60 rounds on Thursday and it ran like a champ! I plan on shooting a lot more when I get a chance to go to the outdoor range. I gotta admit I was kinda nervous when I fired the first shot . There are more accessories to come, I'm eventually going to add some rail protectors, a VFG, an Aimpoint ML3 , a SureFire weaponlight, and a Vickers sling. Then it'll be done!
cpekz - Very nice build! I headed over to Denny's site and checked out those barrels and I'm very impressed. How does it balance? I might have to use one of those barrels for my next middy build because they are extremely impressive.
My lovelies:
DMPS Lower, BM upper, 14.5" 1/7 with Izzy, KAS RAS2, Larue BUIS, LARUE FastFire, Tango Down Vert Grip, Tango Down Pistol Grip, MAgpul CTR Stock, BH Bungee Sling
(Also pictured: Franchi Law-12 and Glock 19, Gerber A/F Fighting Knife)
And the newest addition:
Middy:
Mega Gator Lower w/ DPMS Parts Kit, TD Gip, Magpul CTR, VLTOR MILSPEC Buffer Tube, VLTOR MUR-1A Upper with M4 Extension, WOA 16" Stainless Mid Barrel, Calvary Arms M5 Handguards, Larue SPR-1.5 Mount, Mateck Colt BUIS, Leupold VX-II 20mm 1x4 Scout scope, Troy 1 Point Sling
Edit: Removing Mateck sight, putting 45 degree mount and Burris FastFire on as backup sight.
Bookmarks