Switch to A5 System?

[jahwarrior1423]

I have a 16" mid-length hammer forged BCM upper with the standard A2 flash hider. My lower is a AZ Armory billet lower (dont know the exact trigger brand) but it was worked on by Bill Springfield, and a commercial buffer tube with a carbine buffer and a Magpul MOE buttstock.

I want my rifle to stay reliable with abuse given to it but I want my rifle to become softer shooting. I was doing research on comps but found that I could get a better outcome with "upgrading" my buffer system to an A5 system.

Is this the consensus?

What is all needed for this "upgrade?...just the buffer tube, spring and buffer? Does it work with the Magpul endplate also?

[munch520]

I've really liked the A5 on everything from an 12" carbine system to a 16" middy. I think it works better than a comp and is less limiting. The kit comes with the A5 7-position extension, hybrid buffer, spring, and endplate.

You obviously need the A5 kit, a lower, an armorer's or castle nut wrench, and a center punch/mallet for staking. I didn't like the Magpul end plate when I used it because of the tab you insert into the groove in the buffer tube. I like the end plates that have the tab built in. Make sure you screw the buffer tube in so it captures the retaining pin and so the rear part of the carrier/contacts takes the tension of the buffer face. And stake it!!

[kartoffel]

I have a 16" mid-length hammer forged BCM upper with the standard A2 flash hider. My lower is a AZ Armory billet lower (dont know the exact trigger brand) but it was worked on by Bill Springfield.

If looking to increase reliability, I'd replace the Springfield trigger with either a stock trigger from a known good manufacturer, or with a Geissele unit. But that's just me.

An A5 system certainly couldn't hurt. You will need the A5 receiver extension tube, a rifle length spring, and an A5 buffer weight. Since your current stock is commercial, you'll also need a standard buttstock (or suffer with a loose commercial buttstock on a standard spec RE). You can either get a full-blown A5 kit that includes an Vltor buttstock, or you can order the receiver extension a la carte, plus a the spring and buffer weight in a separate bundle (but no buttstock).

It'll work with any endplate, just like a regular carbean setup. Chances are good that you'll be able to re-stake your old endplate since the castle nut that comes with the receiver extension is unlikely to time exactly the same as your old one. I've re-staked Magpul and Noveske endplates and aside from the extra divots, they work fine.

[SteveL]

I used a Noveske QD end plate when I installed mine. No problems there and I staked it in two places. OP just be sure you never try to use a standard carbine buffer once you replace the receiver extension. The A5 receiver extension is about 3/4" longer than a regular receiver extension and using a standard buffer could cause damage.

[Amicus]

Will the A5 system take any standard rifle spring?

[Hmac]

Will the A5 system take any standard rifle spring?

The A5 system includes the appropriate buffer, buffer tube, and spring.

[Amicus]

I was thinking of replacements for springs. Vltor does not appear to offer them separately.

[markm]

Couldn't it just mean that this is the spring to chose if you're looking for a replacement; not necessarily that it is the spring VLTOR use from the factory?

I hope so. I edited my panic attack reply... It looks like it has a homo redish color to it. I can't imagine the Military messing with CS nonsense.

BTW; the A5 receiver extension is MilSpec diameter then?

Yep!

[skullworks]

Thank you kindly; been wondering about that - and my Google-Fu was weak.

[Amicus]

I hope so. I edited my panic attack reply... It looks like it has a homo redish color to it. I can't imagine the Military messing with CS nonsense.

I sorta had the same response. A casual/quick reading might lead one to your original conclusion.