Call Dillon cause something is out of adjustment. Do that before spending more money in additional dies.
Sent from my DROIDX using Tapatalk 2
Call Dillon cause something is out of adjustment. Do that before spending more money in additional dies.
Sent from my DROIDX using Tapatalk 2
Last edited by lunchbox; 06-09-12 at 15:04. Reason: to add an "A"
^^ Read with southern accent !^^ and blame all grammatical errors on Alabama's public school system.
Technique is nothing more than failed style. Cecil B DeMented
"If you can't eat it or hump it, piss on it and walk away."-Dog
Go where the food is.
There is no reason the Dillon dies should not work perfectly. My swag is it's not the right seater die or somehow defective. Let us know what they say
Sent from my DROID RAZR using Tapatalk 2
The advice about calling Dillon is right on. They will help you figure out what is out of adjustment. Dillon dies are plenty good enough.
Last edited by R600; 06-11-12 at 20:55.
I don't think it is bending the case neck, as least I can't see that it is bent. The crimp doesn't seem to affect it, I have found rounds that are crooked before I crimped them.
I re-adjusted the seating die per the manual last night. With a case in the shell plate I raised the ram and then tightened the die until it made contact with the shellplate. Then I backed the die off two full rotations. Even with the die touching the shellplate it wasn't touching the case, so I don't think it is bending the neck unless the act of seating the bullet is bending the neck. Still no improvement. I also tried a few rounds with the die a half turn tighter (adjusting the seating stem to get the same OAL) to see if that gave the die more time to straighten the bullet before seating. That didn't work either.
I was hoping to get some loads worked up today so I could hit the range tomorrow morning before the heat kicks in. It looks like I will be waiting for Dillon customer service to open up tomorrow morning though. Thanks for all your help guys. If anyone has any other ideas, let me know as I'm willing to try them out.
My only other idea besides Dillon cs is if you had access to a different brand of cases and check to see if the problem still exists. I'm assuming of course that you are resizing the necks already. How well does your bullet fit into your seat die? I've had issues with some Dillon stems or does not fully supporting and straightening my bullet before press with seirra bullets.
The optimal option would be to have the same shape our close so the die sports the tip as well as the body of the bullet and no edges for the bullet to catch on. This would straighten it. If your die doesn't have the right shape in contest to your bullet Dillon may just tell you that a new die is needed to achieve this.good luck in all however.
ETA. I've also experienced crooked bullets when trying to load some compressed powder rounds a hair too much. Reloading is a very trying experiment sometimes and that is one of my examples.
Last edited by Ghost__1; 06-10-12 at 12:47.
That was my guess. Boat tail bullets are almost completely idiot proof which is why I prefer to use them. Ha I'm also curious about the brass being used. I've had issues with some Fed pre primed brass being out of whack. He's already started that its shorter so at least been fired once which may have an impact. There are too many variables at this point for me to try to guess. Dillon should be able to help him.
Last edited by Ghost__1; 06-10-12 at 13:10.
I don't have a concentricity guage, but visual inspection does not reveal any damage to the brass after resizing or in the seating die without a bullet in place. I have set the seating die as per Dillon instructions and also tried with it lower than recommended. Even when I set the seating die all the way down to make contact with the shell plate, it doesn't put any pressure on the case.
I am not using an expander die, and I am not trimming or chamfering/deburring. The brass is once fired Speer. I clean, lube, decap/resize, clean again, clean primer pocket, swage primer pocket (crimped primers), then load. The brass is typically measuring 1.748, which is shorter than the trim-to length and why I am not trimming. I have noticed on a few rounds what appears to be a very small amount of copper jacket shaved off and sitting at the mouth of the case. Also, when I removed the seating stem and placed the bullets in the stem to check the fit, there seems to be a noticable amount of cant that is allowable. Are these potential culprits as well?
Can anyone verify straight loads with .223 Dillon seating dies and 55 gr Hornady FMJBT?
Bookmarks