Page 1 of 17 12311 ... LastLast
Results 1 to 10 of 170

Thread: Review: IWC QD MICRO MOUNT-N-SLOT as installed into a MOE

  1. #1
    Join Date
    Oct 2009
    Location
    Central TX
    Posts
    1,187
    Feedback Score
    17 (100%)

    Review: IWC QD MICRO MOUNT-N-SLOT as installed into a MOE

    I've been following the development of IWC's latest limited rotation QD mount for several months now, and when Earl at IWC offered me the chance to test and evaluate it in one of my midlength MOE handguards I jumped at the chance. (My Momma didn't raise no fools.) Please note the QD MICRO MOUNT-N-SLOT shown here is an unfinished production sample - it is in the final configuration except for application of the black oxide corrosion protection finish that is common to all IWC products.

    IWC's new QD MICRO is designed for dual duty - it direct mounts into any of the holes in a Troy TRX Extreme handguard (yes, even the 1, 4, 7 and 11:00 positions!) but it was also designed to be applicable to all MOE handguards via the drilling of a single 1/2" hole. This MOE modification is very easily done by the user - if I can do it, anyone can.

    The mount itself is a little jewel of modern CNC manufacturing. It's solid steel and has been pared down to be just what's needed for the job with no waste. I forgot to toss it on my gram scale before mounting but it is advertised as being less than a quarter ounce. It inserts into a single 1/2" hole from the inside of the handguard and is retained by a "Spirolock" device on the outside assisted by a pair of setscrews from the inside to prevent the mount from rotating. This is a smart design on the part of IWC - it places all the slinging stresses in compression against the inside of the handguard instead of in tension on the thread of fasteners. All the Spirolock really needs to do is prevent the QD socket from being pressed into the handguard, something it does very effectively. The QD fits well in the space between heat shield and handguard with no issues; I like how it uses a single hole instead of a pair of holes that must be precisely placed. It incorporates a limited rotation feature, too.

    OK, enough background - how to install this puppy?



    Here are the QD components and what I used to install it into my midlength MOE handguard. For tools, I used a 1/2" Forstner bit in a cordless drill for the main hole, a 1/8" drill bit for spotting the setscrew locations and a hobby knife for cleaning up the hole after drilling - any knife will do. Not shown is a small flat bladed jewelers screwdriver that I found to be helpful in installing the Spirolock retainer.



    I first taped the outer and inner surfaces of my MOE to allow measuring and marking and also to protect against tool slips. I projected the slot edges using a steel rule and a pencil and determined the hole's location.

    I then lightly marked the drill location with a center punch and drilled it with a 1/2" Forstner bit in a cordless drill. Go easy and let the bit do the work - Magpul uses a tough polymer for their handguard.



    After the hole was drilled I lightly cleaned up the hole edges by chamfering both sides with a hobby knife.



    Next, I threaded the setscrews into the back of the mount but kept them below flush of the front surface. I inserted and held the QD in place and installed the Spirolock device. It's designed very much like a split keychain ring, you need to gently spread the coil and walk it into the retaining slot. The QD has two slots to accommodate both the thickness of a TRX-E and the thinner MOE - I installed the Spirolock into the outer slot then repeated the process to move it to the inner slot. It's very similar to installing a McFarland gas ring, you gently twist it on like a Slinky. I used a small flat blade jewelers screwdriver to spread the coils and prod the Spirolock into place.



    Magpul's polymer is tough enough that the setscrews work best if you lightly dimple their location on the inside surface of the MOE. I positioned the mount and lightly tightened down the setscrews to mark their position, then backed them off and rotated the QD 90 degrees to expose the spots that were just made. I then centerpunched the positions and used a 1/8" drill bit from the inside to make a pair of shallow dimples for the tips of the setscrews to bed against.

    Last, I rotated the QD back into position, put a dab of threadlocking compound on the setscrew threads and tightened them down. These setscrews do not need to be overly tightened - all they do is snug the QD down and prevent it from spinning in the hole. Don't gorilla them - "farmer tight" is too tight!



    The result is a low profile, low mass limited rotation QD socket that integrates seamlessly into the MOE handguard.

    Many thanks to Earl and the crew at IWC for making this much needed accessory and for giving me the opportunity to get a sneak preview! I think these will be available on their website in the next few weeks, I'm told the production run is off at the finisher's right now.

    ETA: I found a better way of marking the setscrew positions.
    Last edited by HeavyDuty; 04-08-11 at 22:27.
    Ken in Texas

  2. #2
    Join Date
    Jan 2009
    Location
    Republic of Texas
    Posts
    444
    Feedback Score
    4 (100%)
    Excellent review!
    Remember, the Founding Fathers reason for the 2nd Amendment... to combat tyranny. Sadly, when people discuss the 2nd Amendment, the opponents erroneously think it was meant to stand alone... it HAS a preamble:

    "...But when a long train of abuses and usurpations, pursuing invariably the same Object evinces a design to reduce them under absolute Despotism, it is their right, it is their duty, to throw off such Government, and to provide new Guards for their future security..."

    — John Hancock

  3. #3
    Join Date
    Oct 2010
    Location
    Northern Colorado
    Posts
    5,167
    Feedback Score
    60 (100%)
    Good review. Looks like another winner from IWC.

  4. #4
    Join Date
    Oct 2009
    Location
    Central TX
    Posts
    1,187
    Feedback Score
    17 (100%)
    This is the Reader's Digest version; a wordier one is going up at WEvo. The meat's all here, though.
    Ken in Texas

  5. #5
    Join Date
    Oct 2007
    Location
    NW Florida
    Posts
    2,554
    Feedback Score
    43 (98%)
    That is fantastic. I like IWC's stuff, but the original QD attachment for the MOE HG just seemed a little bulky to me. This looks great.

  6. #6
    Join Date
    May 2008
    Posts
    91
    Feedback Score
    0
    I am sold! I want 3, at least.

  7. #7
    Join Date
    Oct 2009
    Location
    Central TX
    Posts
    1,187
    Feedback Score
    17 (100%)
    In another thread Earl pointed out something that is blindingly obvious but that I never thought of - there's no reason you couldn't drill two more holes through the MOE to accept a pair of cap headed machine screws from the outside into the ears. I may try it!
    Ken in Texas

  8. #8
    Join Date
    Jul 2009
    Location
    SE Tennessee
    Posts
    1,153
    Feedback Score
    22 (100%)
    Ken,
    Would a carbine MOE leave enough room to mount one of these in a similar fashion?

  9. #9
    Join Date
    Dec 2009
    Location
    Utah
    Posts
    8,799
    Feedback Score
    3 (100%)
    HD, if you drill the hole completely through, the distance from the 1/2" hole for the cup and the #20 hole for the 8-32 mount screw is very short. As usage will place the mount under tension, it's likely a stress crack will develop between the two holes
    The number of folks on my Full Of Shit list grows everyday

    http://i115.photobucket.com/albums/n289/SgtSongDog/AR%20Carbine/DSC_0114.jpg
    I am American

  10. #10
    Join Date
    May 2010
    Posts
    26
    Feedback Score
    1 (100%)
    Thanks for the good review; I'm interested in several of these, and I know many of my co-workers who would use them as well.

Page 1 of 17 12311 ... LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •