View Full Version : Front sight for Bushmaster Carbon 15 ORC?
So, don't laugh too hard, the market today is what it is, but I bought a Bushmaster Carbon 15 ORC from Gander Mountain a couple of weeks ago to use as a second/beater carbine.
I dislike the cheap Bushnell red dot site it came with and would rather just put straight iron sites on it. The rear site would be the carry handle I took off my 6920.
What are my less expensive but not-too-shitty options for a front site?
caelumatra
01-25-13, 09:53
Could you do an MOE grip and the front MBUS? That would run total around $60 I think. And for a cheapish red dot, I have a Vortex Sparc and its ok. I wouldn't call it tough or anything though
ETA
Or replace the gas block with a standard FSB
Could you do an MOE grip and the front MBUS? That would run total around $60 I think. And for a cheapish red dot, I have a Vortex Sparc and its ok. I wouldn't call it tough or anything though
ETA
Or replace the gas block with a standard FSB
Who has a standard FSB/gas block deal in stock, that I could install without too much difficulty? I thought that might be my best bet, was hoping I could get away with spending/doing less, but just don't know enough to be sure.
$200 is way beyond what I am willing/able to spend for a sighting system on this rifle. This rifle is my lowest priority right now among things that are actually eligible for spending and I'm sure the iron site option will be more durable and longer lived than a mid-range red dot.
caelumatra
01-25-13, 10:25
Midway is the only online shop that estimates return to stock dates so you could look there. I'm surprised that this part is out of stock completely. But I guess people are buying disassembled barrels because that's all they can find
http://www.midwayusa.com/product/593704/daniel-defense-a2-f-marked-front-sight-gas-block-assembly-with-bayonet-lug-ar-15-lr-308-750-inside-diameter-steel-matte
I'd replace with a standard FSB
http://www.bravocompanyusa.com/Front-Sight-Base-s/71.htm
$30 is a pretty good deal...and falls within their minimum order requirement now.
caelumatra
01-25-13, 10:27
Here's the MOE in stock
http://dsgarms.com/ProductInfo/MAG440-OD.aspx
MBUS Gen2 in stock
http://dsgarms.com/ProductInfo/MAG247FG.aspx
If the color you want is out of stock just rattle can it. No one will ever know lol
Here's the MOE in stock
http://dsgarms.com/ProductInfo/MAG440-OD.aspx
MBUS Gen2 in stock
http://dsgarms.com/ProductInfo/MAG247FG.aspx
I already thought of/looked into that. No go.
"Front MBUS must be mounted to a railed fore end on the same plane as the receiver rail. Because of this the sight is also not compatible with MOE Hand Guards."
I'd replace with a standard FSB
http://www.bravocompanyusa.com/Front-Sight-Base-s/71.htm
$30 is a pretty good deal...and falls within their minimum order requirement now.
I was afraid that would be the best answer.
It will be a little more work ("These are new and are not yet drilled for taper pins, and should be installed by a qualified gunsmith.") but shouldn't cost too terribly much.
If I have to ask what it takes to do that, am I not a qualified gunsmith?
lethal dose
01-25-13, 13:00
I was afraid that would be the best answer.
It will be a little more work ("These are new and are not yet drilled for taper pins, and should be installed by a qualified gunsmith.") but shouldn't cost too terribly much.
If I have to ask what it takes to do that, am I not a qualified gunsmith?
It is easy- with the right equipment. That said, few folks have the right equipment. Send it to ADCO and they'll even supply the fsb. I think it's under $150.
It is easy- with the right equipment. That said, few folks have the right equipment. Send it to ADCO and they'll even supply the fsb. I think it's under $150.
Dangit.
I don't have $150 to spend on this front site at this time. If I was in that ballpark I'd say **** it and pring for a Sparc
I was afraid that would be the best answer.
It will be a little more work ("These are new and are not yet drilled for taper pins, and should be installed by a qualified gunsmith.") but shouldn't cost too terribly much.
If I have to ask what it takes to do that, am I not a qualified gunsmith?
Adding a new FSB to a previously drilled barrel will be difficult.
If the new FSB is not drilled in exactly the same spot as the previous pin holes you will remove more material on the barrel. Then when you use the taper ream you may only be reaming the material in the FSB.
Adding a new FSB to a previously drilled barrel will be difficult.
If the new FSB is not drilled in exactly the same spot as the previous pin holes you will remove more material on the barrel. Then when you use the taper ream you may only be reaming the material in the FSB.
Yeah...that's not for me.
The_Hammer_Man
01-25-13, 13:58
"Is gonna be nice to the guy with the Bushy"
PM me.. I have an old, scuffed up F marked NM A-2 FSB in my parts box. All holes present and ready for your pins. Sorry I don't have any taper pins in stock.
another thing that still on backorder :(
Do you have access to a mill?
"Is gonna be nice to the guy with the Bushy"
PM me.. I have an old, scuffed up F marked NM A-2 FSB in my parts box. All holes present and ready for your pins. Sorry I don't have any taper pins in stock.
another thing that still on backorder :(
Sent.
Do you have access to a mill?
Negative.
lethal dose
01-25-13, 14:24
"Is gonna be nice to the guy with the Bushy"
PM me.. I have an old, scuffed up F marked NM A-2 FSB in my parts box. All holes present and ready for your pins. Sorry I don't have any taper pins in stock.
another thing that still on backorder :(
BUT... It's unlikely the holes on your fsb will line up with the milled spots on his barrel.
BUT... It's unlikely the holes on your fsb will line up with the milled spots on his barrel.
Exactly. Basically the same point I was trying to come across above.
The_Hammer_Man
01-25-13, 14:58
hmmm.. I have a NM set screw FSB along with the pinned one that I'll send him. He can send me back the one that didn't work.
No biggy.. doing a favor.
Five_Point_Five_Six
01-25-13, 19:16
"Is gonna be nice to the guy with the Bushy"
PM me.. I have an old, scuffed up F marked NM A-2 FSB in my parts box. All holes present and ready for your pins. Sorry I don't have any taper pins in stock.
another thing that still on backorder :(
hmmm.. I have a NM set screw FSB along with the pinned one that I'll send him. He can send me back the one that didn't work.
No biggy.. doing a favor.
That's good of you. Respect.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.