KingsideRook
04-04-14, 18:43
Sold pending funds.
I have an excellent condition BCM SS410 upper, 90 rounds through it as a pistol. Decided to go as short as possible on the next one. Gorgeous barrel, very accurate even as a pistol. Mid weight profile, soft shooting, and one of the nicest stainless barrels on the market. No complaints at all.
Upper config is:
BCM factory cut-down low-profile pinned FSB
BCM carbine gas tube and roll pin
A2 Flash Hider, and crush washer
BCM GI Barrel nut
BCM A3 Upper complete
Troy FDE 9" Alpha Rail with all 3 rail sections including QD Mount
http://i.imgur.com/YZEN6Jpl.jpg
http://i.imgur.com/7rzwzetl.jpg
http://i.imgur.com/d2X25i8l.jpg
http://i.imgur.com/fX7XzUr.jpg
BCM sells this upper (http://www.bravocompanyusa.com/BCM-SS410-12-5-Carbine-Upper-Receiver-Group-IB-p/bcm-urg-12%20ss410%20ib%20bk.htm)without the Troy Alpha rail, BCG or Charging Handle, for $585 + shipping new. Total new configuration from BCM with Troy rail, BCG and Gunfighter CH, is right at $950 + Shipping, depending on length of rail.
Asking $519 Shipped for the upper without BCM BCG and BCM Gunfighter Mod 4 Charging Handle,
or
$699 Shipped for the upper with matching BCM BCG and BCM Gunfighter Mod 4 Charging Handle, which is a great deal as they are all less than 90 rounds used. All in great shape, very light used and well cared for.
Purchase with confidence, I have good feedback, and would buy this upper again myself. Email with any questions, happy to answer them. All NFA rules apply, etc.
BCM's full specs are as follows:
BCM SS410™ Barrels
This BCM stripped barrel is machined from a 410 stainless steel. It features hand lapped button rifling with a 1/8 twist rate and M4 feedramps. As with all BCM barrels it is proofed (HPT) and magnetic particle inspected (MPI). To give the shooter the best balance of weight and accuracy this BCM barrel has a mid weight profile and a carbine length gas system.
(410 stainless is a harder and more corrosion resistant than the conventional 416 stainless found in most barrels.)
Ionbond coatings advantages
• reduced coefficient of friction
• increased abrasive wear resistance
• antiscuffing/antigalling
• high fretting resistance
• high pitting resistance
• resistance to corrosion and hydrocarbon fuels
• high integrity of surface structure
• good adhesion to base materials
IonBond coatings directly improve wear resistance due to their high hardness, low coefficient of friction and high structural integrity. These coatings with thicknesses of only a few microns and with hardness up to 4000HV, result in increased firearm life and functionality. The IonBonded finishes, absorb oil and release it over time due to the unique characteristics.
Features:
M4 Feed Ramp Barrel Extension
.750 gas block.
Carbine Length Gas System
1/8 Twist Rate
5.56 NATO Match Chambers (SAM-R Chamber)
410 Stainless Steel
Mid Weight Contour Profile Barrels
Button Rifled
Hand Lapped Rifling
HPT (High Pressure Test) Barrels
MPI (Magnetic Particle Inspected) Barrels
I have an excellent condition BCM SS410 upper, 90 rounds through it as a pistol. Decided to go as short as possible on the next one. Gorgeous barrel, very accurate even as a pistol. Mid weight profile, soft shooting, and one of the nicest stainless barrels on the market. No complaints at all.
Upper config is:
BCM factory cut-down low-profile pinned FSB
BCM carbine gas tube and roll pin
A2 Flash Hider, and crush washer
BCM GI Barrel nut
BCM A3 Upper complete
Troy FDE 9" Alpha Rail with all 3 rail sections including QD Mount
http://i.imgur.com/YZEN6Jpl.jpg
http://i.imgur.com/7rzwzetl.jpg
http://i.imgur.com/d2X25i8l.jpg
http://i.imgur.com/fX7XzUr.jpg
BCM sells this upper (http://www.bravocompanyusa.com/BCM-SS410-12-5-Carbine-Upper-Receiver-Group-IB-p/bcm-urg-12%20ss410%20ib%20bk.htm)without the Troy Alpha rail, BCG or Charging Handle, for $585 + shipping new. Total new configuration from BCM with Troy rail, BCG and Gunfighter CH, is right at $950 + Shipping, depending on length of rail.
Asking $519 Shipped for the upper without BCM BCG and BCM Gunfighter Mod 4 Charging Handle,
or
$699 Shipped for the upper with matching BCM BCG and BCM Gunfighter Mod 4 Charging Handle, which is a great deal as they are all less than 90 rounds used. All in great shape, very light used and well cared for.
Purchase with confidence, I have good feedback, and would buy this upper again myself. Email with any questions, happy to answer them. All NFA rules apply, etc.
BCM's full specs are as follows:
BCM SS410™ Barrels
This BCM stripped barrel is machined from a 410 stainless steel. It features hand lapped button rifling with a 1/8 twist rate and M4 feedramps. As with all BCM barrels it is proofed (HPT) and magnetic particle inspected (MPI). To give the shooter the best balance of weight and accuracy this BCM barrel has a mid weight profile and a carbine length gas system.
(410 stainless is a harder and more corrosion resistant than the conventional 416 stainless found in most barrels.)
Ionbond coatings advantages
• reduced coefficient of friction
• increased abrasive wear resistance
• antiscuffing/antigalling
• high fretting resistance
• high pitting resistance
• resistance to corrosion and hydrocarbon fuels
• high integrity of surface structure
• good adhesion to base materials
IonBond coatings directly improve wear resistance due to their high hardness, low coefficient of friction and high structural integrity. These coatings with thicknesses of only a few microns and with hardness up to 4000HV, result in increased firearm life and functionality. The IonBonded finishes, absorb oil and release it over time due to the unique characteristics.
Features:
M4 Feed Ramp Barrel Extension
.750 gas block.
Carbine Length Gas System
1/8 Twist Rate
5.56 NATO Match Chambers (SAM-R Chamber)
410 Stainless Steel
Mid Weight Contour Profile Barrels
Button Rifled
Hand Lapped Rifling
HPT (High Pressure Test) Barrels
MPI (Magnetic Particle Inspected) Barrels