Hootiewho
08-21-15, 06:57
I have an APC inbound and as much as I would like to keep both, that is just not possible. I have a SR25 ECC up for sale. I purchased this rifle new in Apri of this yearl. This is one of the last ECCs to come from KAC, and rolled out with the latest SR25 upgrades such as the 1:10 twist barrel and the duel ejector bolt. It comes with everything that it left the factory with, Sopmod stock, offset 0-600m sights, magazine, box, all paperwork. It is pictured with the MAMS, but I have removed the MAMS and installed it on my APC. The ECC will ship with a regular KAC QDC flash hider.This rifle has a few hundred rounds (less that 400) through it, but has not been run at all like a 5.56mm carbine. I look at these rifles as a semiautomatic precision rifle. If you are looking at this particular rifle, you are in luck as I probably have more data posted online about how it performs than any other SR25 out there. There is a SR25 review posted here...
https://www.m4carbine.net/showthread.php?168761-SR25-ECC-Review
that I wrote on how this rifle shoots with various loads, with pictures ah plenty included. IMHO the barrel is just now getting broken in as I have noticed over the last 100 rounds it is shooting very good for what the intended role of this rifle is. I have posted with the ad the last 10 shot group of FGMM 175 gr I have fired with this rifle. That is a 1” pasty above the group. That was not a slow fire, 20 minute to shoot group, but fired at a pace where a shot was fired as soon as I had a good sight picture again.
If you purchase this ECC I will also email you velocity data for many common factory loads that I chronographed using an Oehler 35P. That will help you with what you need to know to work up a dope chart without having to go to the range or waste ammo looking for velocity data There has been a bipod mounted on the bottom of the rail and a scope mounted to the top. The only scope mounts that have been on it are a GDI and Bobro, so there is very little evidence on the upper of a optic having been mounted. The bipod was mounted with an ADM mount and the rail is clean there as well. The only issue I have had is documented in the review I posted online. It was with Hornady 110 TAP. That said, since break in it has ran that ammo without issue. I am big into precision rifles, so maintenance wise it has been well cared for, and properly cleaned from the chamber forward. There should be no surprises for you the buyer as this rifle is as documented as they come. I am asking $4100 shipped to your FFL. No Trades. If possible, if would be nice if your dealer will take shipment from an individual with a photocopied ID. It will come to you exactly how it came from KAC minus the QDC flash hider but replaced with a MAMS.
http://i135.photobucket.com/albums/q153/hootiewho6933/6BE832FC-15F4-471D-AB00-756D6207BFB7_zpsipzvy3hz.jpg
http://i135.photobucket.com/albums/q153/hootiewho6933/415F6FF6-83B9-4FE1-9E25-E01B1768DD2B_zpsmh61jvzt.jpg
10 shots, 175 gr FGMM. This is the last group I have shot with the rifle.
http://i135.photobucket.com/albums/q153/hootiewho6933/471479e1-48dc-4afb-b62b-9d6bed5a5732_zpstnqo3ewm.png
I prefer discreet PP as gift or 3% for items (do not list anything gun related), but am also fine with money orders. I will discount $50 if you use PP just for logistically reasons on my end. I will ship with tracking immediately when funds are received.
Contact me via email at mclmminsc at gmail dot com and please post in the thread that you are sending an email or that you will take it just incase I am out of email contact but can check the boards for updates. Please EMAIL ME and do not contact via board PM’s as I am not always able to check board PMs.
https://www.m4carbine.net/showthread.php?168761-SR25-ECC-Review
that I wrote on how this rifle shoots with various loads, with pictures ah plenty included. IMHO the barrel is just now getting broken in as I have noticed over the last 100 rounds it is shooting very good for what the intended role of this rifle is. I have posted with the ad the last 10 shot group of FGMM 175 gr I have fired with this rifle. That is a 1” pasty above the group. That was not a slow fire, 20 minute to shoot group, but fired at a pace where a shot was fired as soon as I had a good sight picture again.
If you purchase this ECC I will also email you velocity data for many common factory loads that I chronographed using an Oehler 35P. That will help you with what you need to know to work up a dope chart without having to go to the range or waste ammo looking for velocity data There has been a bipod mounted on the bottom of the rail and a scope mounted to the top. The only scope mounts that have been on it are a GDI and Bobro, so there is very little evidence on the upper of a optic having been mounted. The bipod was mounted with an ADM mount and the rail is clean there as well. The only issue I have had is documented in the review I posted online. It was with Hornady 110 TAP. That said, since break in it has ran that ammo without issue. I am big into precision rifles, so maintenance wise it has been well cared for, and properly cleaned from the chamber forward. There should be no surprises for you the buyer as this rifle is as documented as they come. I am asking $4100 shipped to your FFL. No Trades. If possible, if would be nice if your dealer will take shipment from an individual with a photocopied ID. It will come to you exactly how it came from KAC minus the QDC flash hider but replaced with a MAMS.
http://i135.photobucket.com/albums/q153/hootiewho6933/6BE832FC-15F4-471D-AB00-756D6207BFB7_zpsipzvy3hz.jpg
http://i135.photobucket.com/albums/q153/hootiewho6933/415F6FF6-83B9-4FE1-9E25-E01B1768DD2B_zpsmh61jvzt.jpg
10 shots, 175 gr FGMM. This is the last group I have shot with the rifle.
http://i135.photobucket.com/albums/q153/hootiewho6933/471479e1-48dc-4afb-b62b-9d6bed5a5732_zpstnqo3ewm.png
I prefer discreet PP as gift or 3% for items (do not list anything gun related), but am also fine with money orders. I will discount $50 if you use PP just for logistically reasons on my end. I will ship with tracking immediately when funds are received.
Contact me via email at mclmminsc at gmail dot com and please post in the thread that you are sending an email or that you will take it just incase I am out of email contact but can check the boards for updates. Please EMAIL ME and do not contact via board PM’s as I am not always able to check board PMs.