PDA

View Full Version : Benelli M4 help with Trijicon RMR


dale.gribble
10-13-17, 05:50
I am looking to getting a Trijicom RMR and Scalorworks Rail for my Benelli M4.

Which model RMR should I get 12.9MOA Triangle or 9MOA Dot?
ggammell
10-13-17, 07:03
I am looking to getting a Trijicom RMR and Scalorworks Rail for my Benelli M4.

Which model RMR should I get 12.9MOA Triangle or 9MOA Dot?

In all seriousness, why limit yourself to a dot that large? Why not the 3.25 or 6.5?
tpe187
10-13-17, 11:38
I run a 4 MOA Aimpoint T1 on my Benelli M4. I would advise against the triangle and the larger MOA dots, as you can really stretch the legs on the shotgun with the smaller dots and it will be just as fast to pick up rapidly for close in work.
Evel Baldgui
10-13-17, 12:17
I run a 4 MOA Aimpoint T1 on my Benelli M4. I would advise against the triangle and the larger MOA dots, as you can really stretch the legs on the shotgun with the smaller dots and it will be just as fast to pick up rapidly for close in work.

Good point..Was just reading this thread for info and picked some good advice ! Thank you!
GJM
10-13-17, 12:47
Your Benelli is a a tough as nails shotgun, why pick an RMR which is light duty by comparison, when an Aimpoint micro is an option?
GH41
10-13-17, 14:25
Your Benelli is a a tough as nails shotgun, why pick an RMR which is light duty by comparison, when an Aimpoint micro is an option?

I like ribs and beads and would probably never get either but I would choose the RMR over a micro if I did. Height alone would drive my decision. If the gun fits you with the factory ghost rings it'll still fit with the RMR on the Scalarworks mount . It won't with the jacked up Micro.
GJM
10-13-17, 15:19
I like ribs and beads and would probably never get either but I would choose the RMR over a micro if I did. Height alone would drive my decision. If the gun fits you with the factory ghost rings it'll still fit with the RMR on the Scalarworks mount . It won't with the jacked up Micro.

I have an M4 with the Scalarworks/T2 combo and the factory iron sights are perfectly usable through the tube of the Micro.

47994
GH41
10-13-17, 16:48
I have an M4 with the Scalarworks/T2 combo and the factory iron sights are perfectly usable through the tube of the Micro.

47994

Didn't say it would be unusable, I said if the gun fits you with the irons it will not fit you with the T2. Probably won't fit with the RMR either but it will be closer.
WS6
10-15-17, 03:29
I like ribs and beads and would probably never get either but I would choose the RMR over a micro if I did. Height alone would drive my decision. If the gun fits you with the factory ghost rings it'll still fit with the RMR on the Scalarworks mount . It won't with the jacked up Micro.

It actually sits lower than the RMR. I went h2 4 moa.
SOWT
10-18-17, 13:36
Didn't say it would be unusable, I said if the gun fits you with the irons it will not fit you with the T2. Probably won't fit with the RMR either but it will be closer.

My RMR is co-witnessed to the Benelli iron sights.
GH41
10-18-17, 17:14
What's wrong with these 2 examples?
4809348094
hk_shootr
11-09-17, 23:48
Didn't say it would be unusable, I said if the gun fits you with the irons it will not fit you with the T2. Probably won't fit with the RMR either but it will be closer.

T2 can co-witness with factory sights with the proper mount