Warg
09-18-09, 11:59
SOLD
I built this as a gift, but the person I built it for declined the offer :eek:
This upper has never been fired and has the following:
YHM 5.56 20" fluted CMV, 1:7 twist, fluted heavy chrome-lined barrel, Duracoated in Magpul FDE. M4 feedramps ($203)
BCM A4 flat top upper receiver with M4 feedramps($109)
YHM lightweight rifle length handuard ($145)
VLTOR low profile gas block ($50)
crush washer ($2)
gas tube, rifle length + roll pin ($15)
Magpul MBUS, rear ($55)
Magpul MBUS, front ($38)
Magpul XT ladder covers, FDE ($23)
Magpul long rail ladder cover, FDE ($12)
A2 flash hider ($14)
LMT auto BCG ($135)
BCM charging handle ($24)
Total without BCG and CH = $666, will let it go for $460
Total with BCG and CHG = $825, will sell for $575
As mentioned, I have not fired this upper, but did perform a function check using dummy rounds. It works perfectly. The Magpul FDE Duracoat is a shade or two lighter than the Magpul components, BTW. The gas block is the VLTOR set screw type that was installed with the BRD dimple jig. It is not pinned, but is very secure. Also somes with a YHM sling swivel stud on the rail and a YHM handguard wrench ($30) included at no extra charge! Have all receipts.
Some pics below (not selling the lower, of course):
http://i304.photobucket.com/albums/nn176/Dr_Wolfenstein/ARs/Allbutladders2_sm2.jpg
http://i304.photobucket.com/albums/nn176/Dr_Wolfenstein/ARs/IMG_2078.jpg
http://i304.photobucket.com/albums/nn176/Dr_Wolfenstein/ARs/IMG_2079.jpg
http://i304.photobucket.com/albums/nn176/Dr_Wolfenstein/ARs/IMG_2081.jpg
The prices reflect roughtly a 30% discount of off retail- not including the shipping I had to pay.
Prefere PayPal plus 3% and shipping.
Smoking deal!
Thanks,
Gene
I built this as a gift, but the person I built it for declined the offer :eek:
This upper has never been fired and has the following:
YHM 5.56 20" fluted CMV, 1:7 twist, fluted heavy chrome-lined barrel, Duracoated in Magpul FDE. M4 feedramps ($203)
BCM A4 flat top upper receiver with M4 feedramps($109)
YHM lightweight rifle length handuard ($145)
VLTOR low profile gas block ($50)
crush washer ($2)
gas tube, rifle length + roll pin ($15)
Magpul MBUS, rear ($55)
Magpul MBUS, front ($38)
Magpul XT ladder covers, FDE ($23)
Magpul long rail ladder cover, FDE ($12)
A2 flash hider ($14)
LMT auto BCG ($135)
BCM charging handle ($24)
Total without BCG and CH = $666, will let it go for $460
Total with BCG and CHG = $825, will sell for $575
As mentioned, I have not fired this upper, but did perform a function check using dummy rounds. It works perfectly. The Magpul FDE Duracoat is a shade or two lighter than the Magpul components, BTW. The gas block is the VLTOR set screw type that was installed with the BRD dimple jig. It is not pinned, but is very secure. Also somes with a YHM sling swivel stud on the rail and a YHM handguard wrench ($30) included at no extra charge! Have all receipts.
Some pics below (not selling the lower, of course):
http://i304.photobucket.com/albums/nn176/Dr_Wolfenstein/ARs/Allbutladders2_sm2.jpg
http://i304.photobucket.com/albums/nn176/Dr_Wolfenstein/ARs/IMG_2078.jpg
http://i304.photobucket.com/albums/nn176/Dr_Wolfenstein/ARs/IMG_2079.jpg
http://i304.photobucket.com/albums/nn176/Dr_Wolfenstein/ARs/IMG_2081.jpg
The prices reflect roughtly a 30% discount of off retail- not including the shipping I had to pay.
Prefere PayPal plus 3% and shipping.
Smoking deal!
Thanks,
Gene