serevince
12-01-11, 22:22
I'm trying to finish my "perfect all around" build, which has turned into the "my wallet is empty" build.:D
I have the Nordic 14.5 free float hand guard and want to mount just enough rail to get a DD fixed BUIS and a X300 at the 12 o'clock position.
I measured my x300 at 2.5"-3.5" of rail attachment depending on how much it overhangs the tube at the end. I'm going to err towards 3.5". I think if I mount it near flush with the FF tube the lens will stay cleaner during firing.
I'm guessing I need at least 1.5" for the DD fixed front BUIS, but I'm allowing for 2". (Haven't ordered the DD BUIS yet)
NC does not make a 12'oclock 6" rail. 3.35", 9", and 12" are the only options. I have a 3.35" on the on the way as a stop gap measure (just released this week).
Before I order a 9" and have it cut;
Can any of the tech wizards on here tell me if there is a 6" version made by another manufacturer that is the correct height for a 12 o'clock mount and compatible with the NC tube?
Note:The 3.35" is chamfered at each end so I can't just use 2 of them without a gap.
Nordic Components (http://shop.nordiccomp.com/Picatinny-Rail-for-the-NC1-Style-Mid-Length-Hand-Guard-TRL-NC1-MID.htm)
Thank you
Vince
Build specs: (red is not ordered yet or TBD)
BCM blem stripped upper
BCM CHF 16" mid/LW shaved FSB
BCM BCG
NC 14.5" free float hand guard
Griffin Armament M4-SD brake
DD fixed front BUIS
Optic/mount
rear BUIS (DD fixed?)
ACLM CH
CMMG lower
Geissele SSA-E
VLTOR A5 system
Stock (MP STR or SOPMOD)
VTAC wide sling
Duracoat tactical FDE on stripped upper/lower/handguard
all levers/dustcover/barrel/ sights/ foward assist/ CH etc left factory black
I have the Nordic 14.5 free float hand guard and want to mount just enough rail to get a DD fixed BUIS and a X300 at the 12 o'clock position.
I measured my x300 at 2.5"-3.5" of rail attachment depending on how much it overhangs the tube at the end. I'm going to err towards 3.5". I think if I mount it near flush with the FF tube the lens will stay cleaner during firing.
I'm guessing I need at least 1.5" for the DD fixed front BUIS, but I'm allowing for 2". (Haven't ordered the DD BUIS yet)
NC does not make a 12'oclock 6" rail. 3.35", 9", and 12" are the only options. I have a 3.35" on the on the way as a stop gap measure (just released this week).
Before I order a 9" and have it cut;
Can any of the tech wizards on here tell me if there is a 6" version made by another manufacturer that is the correct height for a 12 o'clock mount and compatible with the NC tube?
Note:The 3.35" is chamfered at each end so I can't just use 2 of them without a gap.
Nordic Components (http://shop.nordiccomp.com/Picatinny-Rail-for-the-NC1-Style-Mid-Length-Hand-Guard-TRL-NC1-MID.htm)
Thank you
Vince
Build specs: (red is not ordered yet or TBD)
BCM blem stripped upper
BCM CHF 16" mid/LW shaved FSB
BCM BCG
NC 14.5" free float hand guard
Griffin Armament M4-SD brake
DD fixed front BUIS
Optic/mount
rear BUIS (DD fixed?)
ACLM CH
CMMG lower
Geissele SSA-E
VLTOR A5 system
Stock (MP STR or SOPMOD)
VTAC wide sling
Duracoat tactical FDE on stripped upper/lower/handguard
all levers/dustcover/barrel/ sights/ foward assist/ CH etc left factory black