On your Noveske Afgan. You should not bridge the optic from the receiver to the rail. The scope is also too forward. Not sure how you are able to shoot it like that..
Pat
Printable View
Pat u r correct on the scope hitting the buis(troy) that is why. I don't
have any problems shooting like it is set up. Bridging the scope is probably why I can't get the groups I expect from the Noveske barrel. I'm gonna switch the arms mount to a Larue and that will be better thanks Chad
You can always run a A.R.M.S. Swan Sleeve which will kill two birds with one stone...first it will provide you the clearance to clear the rear buis w/o switching rings or buying a new mount, secondly it will mate up your separated upper rec. and rail better and overall making it more rigid for mounting optics.
The worst way to mount glass on an AR 15 is to run separate rings with one on the upper rec. and the other on the rail...like the above setup. I still would not bridge the gap with a one piece mount like a larue or adm. The Swan Sleeve has a place in the AR builder's repertoire of kit and it seems like you might could benefit from the use of one.
http://i106.photobucket.com/albums/m...9/DSC00056.jpg
http://i106.photobucket.com/albums/m...9/DSC00058.jpg
- spikes lower
- colt upper
- magpul prs
- daniel defense omega 12
- vltor low profile gas block
- advanced armament corporation blackout
- dez arms 20 inch heavy bbl
- harris bipod
- leupold vx-i
- forgot to put on the mbus because i was too excited to have completed the build... :)
Bravo Company MK12 SPR
18" BCM SS410
http://farm6.static.flickr.com/5167/...ebf9642c_b.jpg
Federal Gold Medal Match 77gr
http://i886.photobucket.com/albums/a...R77grgroup.jpg
Federal Gold Medal Match 69gr (I called the lower left pulled round. Aaarrrggghhh).
http://i886.photobucket.com/albums/a...R69grgroup.jpg
http://farm6.static.flickr.com/5245/...a5725861_b.jpg
Daniel Defense Recce
16" Lothar Walther LW50 barrel
http://farm6.static.flickr.com/5124/...bec2330a_b.jpg
Daniel Defense group of 5 FGMM 77gr rounds.
http://i886.photobucket.com/albums/a...e77grgroup.jpg
well, even though it doesn't have a scope, I figure I should post this in the sub-forum I helped get started (thanks again).
and I have a target to go with it :D
http://www.danpassaro.com/img/s7/v7/p34502222.jpg
http://www.danpassaro.com/img/s9/v15/p434030304.jpg
My new 20" White Oak Armament barreled upper...
http://i62.photobucket.com/albums/h1...ewRifle106.jpg
http://i62.photobucket.com/albums/h1...iscpics037.jpg
http://i62.photobucket.com/albums/h1...iscpics041.jpg
Optic: Bushnell Elite 6500 with MILDOT Reticle (2.5-16 power)
Rings: Burris P.E.P.R.
Upper: WOA 20" Varmint
Tube: Yankee Hill Float Tube (Will be changing this out for a VTAC or TRX.
Lower: The one pictured is from my 18" WOA SPR
Lower for THIS rifle: LCW "superior" Lower, Geissele SD-E, MAGPUL BAD, Ambi-Safety, ERGO Grip with adjustable palm shelf, buffer / spring / tube will be determined by the stock I decide on...
Stock: Have not made my mind up between the MAGPUL UBR or PRS
Bipods: Harris for now, looking seriously at the Tango Down unit or Versa-Pod.
Damn good shooting Danpass!