Mid Length hand guard upgrade

Printable View

03-15-19, 21:10
NotDr.Phil

Mid Length hand guard upgrade

Hi All:
Newbie when it comes to AR15’s (though not guns).
Just got an M&P 15 Optics Ready & want to upgrade from stock
carbine length handguard to a Mid Length Magpul hand guard
(MAG426).

I know the mid length is about 2 or 2.5 inches longer.
If I make this change, do I need to remove & reposition
the gas block and install a longer gas tube? OR does the
Mid length just drop in?
03-15-19, 21:19
opngrnd

Quote:

Originally Posted by NotDr.Phil

Hi All:
Newbie when it comes to AR15’s (though not guns).
Just got an M&P 15 Optics Ready & want to upgrade from stock
carbine length handguard to a Mid Length Magpul hand guard
(MAG426).

I know the mid length is about 2 or 2.5 inches longer.
If I make this change, do I need to remove & reposition
the gas block and install a longer gas tube? OR does the
Mid length just drop in?

I'm afraid you won't be able to change the handguards in that manner. Moving the gas block isn't an option because the purpose of the gas block is to sit over the gas port and direct gas through the gas tube into the action. Being that the gas port is a hole drilled into the top of the barrel, the gas block needs to be at its present location unless the barrel is replaced with a barrel that has a different gas system or you sent the upper out to have the gas port welded and a new gas port drilled.

Consider this longer, more ergonomic handguard that fits your carbine length gas system, but is about the same length overall as the mid-length MOE you are asking about:

https://www.magpul.com/products/moe-...uctColor=VO343
03-15-19, 22:46
Rascally

Quote:

Originally Posted by taekwondopreacher

I'm afraid you won't be able to change the handguards in that manner. Moving the gas block isn't an option because the purpose of the gas block is to sit over the gas port and direct gas through the gas tube into the action. Being that the gas port is a hole drilled into the top of the barrel, the gas block needs to be at its present location unless the barrel is replaced with a barrel that has a different gas system or you sent the upper out to have the gas port welded and a new gas port drilled.

Consider this longer, more ergonomic handguard that fits your carbine length gas system, but is about the same length overall as the mid-length MOE you are asking about:

https://www.magpul.com/products/moe-...uctColor=VO343

This is the easiest and least expensive answer for what you want to do. Otherwise, as noted, new barrel.
03-15-19, 23:05
Iraqgunz

Sell the upper and get a midlength. Or be prepared to get a new barrel, handguards, etc..

Quote:

Originally Posted by NotDr.Phil

Hi All:
Newbie when it comes to AR15’s (though not guns).
Just got an M&P 15 Optics Ready & want to upgrade from stock
carbine length handguard to a Mid Length Magpul hand guard
(MAG426).

I know the mid length is about 2 or 2.5 inches longer.
If I make this change, do I need to remove & reposition
the gas block and install a longer gas tube? OR does the
Mid length just drop in?
03-16-19, 02:29
titsonritz

Just don't be like this guy...
https://www.m4carbine.net/showthread...ilure-to-cycle
03-16-19, 15:15
AndyLate

Quote:

Originally Posted by titsonritz

Just don't be like this guy.

Was that real or a troll?
03-16-19, 17:47
Rascally

Quote:

Originally Posted by AndyLate

Was that real or a troll?

It could have been real. My LGS guy showed me a rifle someone had dropped off for the same issue, non-cycling. It had been assembled by a third party, a "friend". We both had a good laugh, because the gas block was 1/2" off the gas port shoulder.

There are a whole lot of people driving cars that don't have the faintest idea of what to do with a flat tire...
03-16-19, 19:19
titsonritz

Quote:

Originally Posted by AndyLate

Was that real or a troll?

Totally real and not the only one.