what is the best comp that requires little to no timing . I need to install and pin the comp. I would not be able to go to the range and play wit it.
Printable View
what is the best comp that requires little to no timing . I need to install and pin the comp. I would not be able to go to the range and play wit it.
I'm sure ther are some that require little timing, but a comp or at least the ones I am familiar with, require timing to do thier respective job. There are many that do a fine job that have been discussed at length on this site.
Good luck
Miculek is pretty forgiving but you can visually time a comp with either crush or peel washers and then pin it. Many comps can have a jet port drilled and then you can open it up in small increments to tune the comp. I drilled and tapped my Nordic comp for a machine screw which I drilled a small hole in the center of because I had a little too much downforce.
I don't understand the question. There is no need to install/time a comp and then go to the range. All that you need to do is follow the instructions. Most all of them will tell you how to do it.
I recommend a Bravo Comp that is designed for that purpose and is already pre-drilled.
It seems to me that the very nature of an effective compensator mandates that it be timed.
Anyway, what's the big beal with timing? Crush washer, tighten-loosen-tighten-loosen-tighten-loosen until you're 90 degrees short of timed, give it that last 90 degrees and you're done. It's a 5 minute project. Only way to screw it up is if you go past optimal timing too much, in which case you grab another crush washer and start over.
Why would you need to go to the range?
Get an effin a comp and you can tune it after it is pinned.
Agreed with others that 'timing' it is very simple and doesn't require a range trip so long as you follow the instructions on 95+% of comps.
Just to ensure we give the answer you're looking for---do you prioritize a lack of muzzle climb, felt recoil, blast, ect... when defining "best?"
+1 for the BCM Comp. I have one on my 14.5 pinned and welded. It works well as both a comp and a flash hider.I like how my M9 Phrobis Bayonet will fit with it as well. I tried it on my 10.5 and while it helped with muzzle rise it was SOOO loud, even with electronic earpro. And of course it did nothing for the flash. Nothing much will on a shorty tho.
OP, I third the motion for a BCM comp. I have one pinned on a 14.5" BCM upper I built. It took about 15 minutes to attach, drill the barrel, pin & weld. Pretty simple
Sent via Tapatalk
Try Griffin Armament comps. They're quality and they work.
OP, crush washers are cheap. Buy a pack of 10 and play with as many comps as you need to until you're satisfied and settle for one. Timing is nothing. Red Loctite that shit down after you've settled on a comp you prefer.
BCM's comp is great as previously mentioned. Battlecomp makes an excellent product that I've been happy with and if you plan to suppress the Surefire brakes are excellent but very loud and do little to alleviate flash.
I've not tried the BCM, but I respect the brand and the price makes it worth considering if starting from scratch.
I have BattleComp 1.0 on all my rifles, including two 11.5 SBRs and have not had any reason whatsoever to consider anything to replace them. And BCE's customer service is truly extraordinary.
I did have a PWS FSC556 on a 16 inch barrel for awhile. That did suck.
Off the top of my head, the only comps that would require range time would be the Effin-A and B comps and that would only be for 'fine tuning' which ports you want to have screws in.
Love my Battle Comps 1.0 and 1.5 and 2.0 on my 5.56's and BABC on my 6.8 and 300BLK.
Lanrac Dragon
Off the top of my head, the only comps that would need range time would be the Effin-A and B comps and that is only for fine tuning (deciding which screws you want to leave installed or not). Everything else should be pretty obvious and easy to time without going to the range as previously mentioned.
Okay, I was just curious. I have owned 2. One 556 and a .30 cal for the 6.8. I love them.
I was shooting beside a buddy last week with his gun having a surefire brake and mine the PWS, both on a 16" BCM barrel.
The three of us there thought mine had less concussion and both of the other guys are talking about switching to PWS for function after shooting both rifles.
I guess it all comes down to personal preference and personal interpretation of function.
It is much louder than a standard A2, though.
Thank you all. for you in put. I have not been able to respond. a flat shooting rifle to me is the most important. living in Connecticut to day all I need is to get stopped with unpinned 14.5 barrel. I would make 6 o'clock news fast. that's why I just want to pin it and forget about it.
Side ported brakes seem to shoot very flat. The Miculek, and Lantac Dragon do a great job at that but they're pretty blasty.
http://imageshack.us/a/img837/8292/1qbh.jpg
For a little less blast but still good control of muzzle rise the Battlecomp and Manticore NightBrake are very effective as well.
My Battlecomp review with day/night shooting
My NightBrake review with day/night shooting