Any of you folks pleased with the results? I am considering trying it out on my M4. What say you? What brand? Thanks...
Printable View
Any of you folks pleased with the results? I am considering trying it out on my M4. What say you? What brand? Thanks...
Gunslick Foaming Bore cleaner has always done the trick for me.
Spray it in, let it set for 30 minutes, brush out, followed by patches.
I don't do this very often though, maybe ever 1000 rounds.
https://www.m4carbine.net/showthread...m-Bore-cleaner
https://www.m4carbine.net/archive/in...p/t-21372.html
https://www.m4carbine.net/showthread...-good-for-ARs-!
https://www.m4carbine.net/archive/in...p/t-44610.html
Search results. there is a bunch more.
Personally I do not use them. But everyone has their own methods as to what works. I have used M-pro foaming CLP and did not really like it much, it was the only M-pro product I was not happy with. I really like JB non embedding bore cleaner and JB bore-brite every 1000 rounds.
I have shooters choice foaming bore cleaner that has always done a great job. Haven't tried anything else though in terms of foaming bore cleaner.
I use Breakfree Foam Bore Cleaner about every 500 rounds and Ballistol about every 100 rounds in between. Ripcord through the bore before leaving the range every time while the barrel is still warm.
Switched to brake cleaner sprayed through barrel.
Gun slick is great; use that followed by a bore snake, then a patch soaked in Slip 2000 EWL.
I've always had good luck with it
Not sure about other cleaners but I know that Gunslick does not recommend use of its foaming bore cleaner in DI weapons. If the gas tubes are not cleaned out, the foam can gum up and form a gel in the tube.
I've found it works out fine, though, if you use compressed air to blow out the tube.
What are ya'll trying to accomplish by cleaning the bore?
Unless I get sand or dirt in it, I never try to clean any bore unless it's lost accuracy (which is extremely rare).
Removing copper buildup
I still don't understand. Have 5000+ rounds easily through one of my SBRs and I've never used anything more than a boresnake through it.
I also shoot regularly to 300 yards, but only use M855. Accuracy is still acceptable.
Are these regimens for Recce's with 77gr ammo? Not being a dick, genuinely curious. I've never once removed copper from a bore of anything other than bolt guns.
What Euro is getting at, is that copper in a chrome lined bore doesn't hurt anything.
I put a little over 12K through a Colt SOCOM barrel and it was cleaned twice, copper never removed. I could not detect any accuracy difference at 12K.
I have a stainless barrel.
There are almost as many gun cleaning philosophies as there are guns and I don't think there is a right one or wrong one. It's whatever you prefer to do.
Wipe Out give me the most green on the patches, and you can leave it in however long you like.
I did an experiment with Sweet's 762 on a sectioned barrel, dabbing a little on each day, same spot. Seeing if I could see any kind of damage or explanation for the "don't leave it on longer than 15 minutes" thing. No harm I could see-- just a very clean spot!
I've been using a foam cleaner in my stainless barrel as well, the Break Free version. It makes cleaning a breeze and leaves the bore immaculate. It's ammonia free and supposedly non-toxic.
I've experimented with putting disassembled bolt parts into a glass bowl and covering them with the foam. After fifteen minutes, the parts wipe clean with a paper towel.
My understanding is that you want to use an ammonia free product with stainless barrels. The Break Free foam and a few other brands are ammonia free.
Also, you don't want to leave the foam in more than 15-30 minutes according to the recommendations I've seen. Supposedly, you can get some etching in your bore if you leave it in overnight or longer. I'm not sure if that's true of ammonia free products, but I err on the side of caution.
If you have a lot of fouling, you'll see a bunch of blue green runoff. You'll want to soak that up with patches, chamber mop, etc.
I really don't think it's necessary to go beyond a carbon solvent like mpro7. I personally know of many .308 match barrels shooting lights out beyond 8,000 without anyone pulling copper out.