Will a speedloader stress the crane

[aceofspades991]

Hi all,

I recently purchased a S&W 642 and I'm looking into different speedloaders. I bought an HKS but I don't like having to turn the knob, so I'm looking into the Safariland Comp 1 and the SL Variant (when they are available again) but I'm concerned that pressing them into the cylinder repeatedly may put to much stress on the crane or other related components, have any of you experienced issues with these speedloaders or is this not a legitimate concern.

Thanks,
Ace.

[Alaskapopo]

Hi all,

I recently purchased a S&W 642 and I'm looking into different speedloaders. I bought an HKS but I don't like having to turn the knob, so I'm looking into the Safariland Comp 1 and the SL Variant (when they are available again) but I'm concerned that pressing them into the cylinder repeatedly may put to much stress on the crane or other related components, have any of you experienced issues with these speedloaders or is this not a legitimate concern.

Thanks,
Ace.

Not an issue I have been using Safariland speed loaders for a while.
Pat

[Straight Shooter]

Ive been using 3 of the EXCELLENT Comp 2's for my SP101 for awhile now. I see no problem. Learn a good technique. And MOST IMPORTANTLY..DO NOT slam the cylinder closed like the ****in idiots on tv and in the movies. ROLL IT shut.
Also///try the SPEEDSTRIPS. I LOVE them.

[aceofspades991]

Thanks for the replies! I'll have to order some soon.

[chris914]

I have not used them in the J-Frame but I have used them in IDPA for the past several months in my K-frame. More expensive than the others but they have performed better for me.

[fotomaker57]

Only if you get way to heavy handed

[DocH]

I have not used them in the J-Frame but I have used them in IDPA for the past several months in my K-frame. More expensive than the others but they have performed better for me.

I second the motion for the Jet Loaders.I've used them for decades.Have a drawer full of them for K frames.Never a problem. Check Buffer Technologies. They cost more now,but I think I paid around 9 bucks apiece for all mine.

[aceofspades991]

Thanks for all the replies! I won't worry about this issue anymore. Just from looking at the design, I like how the SL Variant is triggered by the ejector, not a button on the back, that way I know it wont go off until is properly seated in the cylinder. If they don't come back in stock soon, I may get one instead.

[Flashman]

I have had no problems with J, K or N frames using speedloaders however I have had problems with SP101's and GP's. It seems Rugers' have some kind of spring retention system to hold the crane pivot assembly into the frame. When applying pressure to the cylinder such with a Safariland speedloader, on some Ruger's, the entire crane pivot assembly will pop out of the frame. How far depends on the gun. I have been told a little movement is normal. Once the pressure is removed, it is supposed to pop back into place. However, this didn't occur on my recently newly purchased SP which Ruger just replaced. The second one has the same problem but not to the degree as the first one.

It becomes a problem if the crane pivot assembly does not return to its' default position because the cylinder will not close.

I suspect the work around is to use HKS speedloaders, which are slower in my view and not as reliable as Safarilands. Holding the cylinder very firmly in the support hand as free from contact with the frame as possible so that the full force of the forward push from the speedloader to release the cartridges is confined to the cylinder only will minimize the tendency for the crane pivot assembly to pop out from the frame.

I am a little disappointed with Ruger over this problem. That said, I have seen several very competent competitors aggressively load their GP's slamming Safariland III's into unsupported cylinders with no apparent ill effects.

[aceofspades991]

That sucks, I hope ruger can sort that out for you. Thanks for the input.