Page 2 of 14 FirstFirst 123412 ... LastLast
Results 11 to 20 of 132

Thread: Black Hills 5.56mm 77 gr TMK and 69 gr TMK Review

  1. #11
    Join Date
    Jun 2009
    Location
    AZ
    Posts
    5,465
    Feedback Score
    6 (100%)
    Another notable, but should be obvious with the SD's Mark posted, the ammo shot sub moa. It also shot sub moa out of my SPR Reece ish guns. One has a Centurion barrel and one has a NOVESKE. Both 16 inch tubes.

    I think my Noveske is so nasty dirty it took about 30 rounds burnt through it before the groups tightened up. It didn't shoot great, so I went back to our house load, shot like shit, .....asked Mark shoot it a while. Then at the end, it shot a nice sub moa group. Time to bore swab that bad boy.
    "Air Force / Policeman / Fireman / Man of God / Friend of mine / R.I.P. Steve Lamy"

  2. #12
    Join Date
    Sep 2007
    Location
    AZ
    Posts
    26,264
    Feedback Score
    14 (100%)
    Quote Originally Posted by 556Cliff View Post
    It's good to see you give Black Hills a shot, as long as you don't go all out full gueer and start using Sprinco springs and LWRC piston rifles.
    I had to put some Springcos into a few of Pappabear's guns. I thought about throwing them out and subbing correct springs.
    "You people have too much time on your hands." - scottryan

  3. #13
    Join Date
    Feb 2008
    Location
    Washington
    Posts
    749
    Feedback Score
    0
    Quote Originally Posted by markm View Post
    I had to put some Springcos into a few of Pappabear's guns. I thought about throwing them out and subbing correct springs.
    Wow, that's bad but Pappabear has always been a bit more of a hippie than you... Are those the Sprinco springs that that "enabler" Iraqgunz gave you guys?

    I only buy Colt springs.
    Last edited by 556Cliff; 03-28-17 at 11:44.

  4. #14
    Join Date
    Aug 2009
    Posts
    40
    Feedback Score
    0
    Pappabear, did you get a chance to chrono it out of your 16" guns?

    Have you guys had a chance to test any of the other popular faux MK262 loads? I was all about my Defender stuff but the velocities seem a little low compared to the real thing...

  5. #15
    Join Date
    Jun 2009
    Location
    AZ
    Posts
    5,465
    Feedback Score
    6 (100%)
    Quote Originally Posted by bfk4lyfe View Post
    Pappabear, did you get a chance to chrono it out of your 16" guns?

    Have you guys had a chance to test any of the other popular faux MK262 loads? I was all about my Defender stuff but the velocities seem a little low compared to the real thing...

    We are going to do that next just confirm data. But we did it on the first run of BH stuff and it was solid.
    We will run 16, 14.5, 11.5, 10.3 and post.

    We were thinking about doing them with and without cans.

    PB
    Last edited by Pappabear; 03-28-17 at 19:11.
    "Air Force / Policeman / Fireman / Man of God / Friend of mine / R.I.P. Steve Lamy"

  6. #16
    Join Date
    Jun 2009
    Location
    AZ
    Posts
    5,465
    Feedback Score
    6 (100%)
    Quote Originally Posted by markm View Post
    I had to put some Springcos into a few of Pappabear's guns. I thought about throwing them out and subbing correct springs.
    All he would have done is put them in his guns. He loves my Sprincos , I saw his eyes when he looked at them. Can't fool a Pappabear.
    "Air Force / Policeman / Fireman / Man of God / Friend of mine / R.I.P. Steve Lamy"

  7. #17
    Join Date
    Sep 2007
    Location
    AZ
    Posts
    26,264
    Feedback Score
    14 (100%)
    Quote Originally Posted by bfk4lyfe View Post
    Have you guys had a chance to test any of the other popular faux MK262 loads?
    We haven't. When you can load your own, it's not often that you buy very many factory loads. If I saw some of the options locally, I'd pick up a box or two to play with. Oddly enough.. I hate going into gun stores.
    Last edited by markm; 03-28-17 at 23:36.
    "You people have too much time on your hands." - scottryan

  8. #18
    Join Date
    Apr 2007
    Location
    Texas
    Posts
    10,421
    Feedback Score
    43 (100%)
    I did a little bit of thread surgery here. This thread has great potential, and I'd love to see it stay on track. Thank you.

    I'd also be really interested on the data from various barrel lengths, both suppressed and unsuppressed.

  9. #19
    Join Date
    Sep 2007
    Location
    AZ
    Posts
    26,264
    Feedback Score
    14 (100%)
    Thanks. Yeah... I think Pappabear is bringing his chrono next time. My model of Magnetospeed won't work with suppressors.
    "You people have too much time on your hands." - scottryan

  10. #20
    Join Date
    Oct 2012
    Location
    Midwest
    Posts
    5,128
    Feedback Score
    1 (100%)
    Quote Originally Posted by markm View Post
    Thanks. Yeah... I think Pappabear is bringing his chrono next time. My model of Magnetospeed won't work with suppressors.
    I thought you guys had a Labradar too?
    Quote Originally Posted by JSantoro View Post
    Stop dicking the dog, please. It's gross.

Page 2 of 14 FirstFirst 123412 ... LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •