M-16 Bolt Carrier Group – TF – Chrome Lined Phosphate
Bolt precision machined from Carpenter 158; carburized/case hardened & shot peened
HP proof testing, 100% using a high pressure M197 or SAAMI commercial equivalent, without evidence of failure
MPI testing after above, 100% inspection per ASTM E1444 using a standard 5 turn magnetizing coil with a current of 200 to 300 amperes. Circular and longitudinal continuous magnetization and a wet fluorescent solution shall be used. Conformance to MIL-STD-410 is required within ASTM E1444
Ultrasonically cleaned and manganese phosphate – 2 hours accelerated Salt Spray & 48-hour endurance Salt Spray completed on each lot
Markings laser engraved (HPT=High Pressure Tested, MPI=Magnetic Particle Inspection)
Extractor, machined 4140 Tool steel alloy, hardened with manganese phosphate
Extractor Pin, precision machined and ground AMS6440/52100 Bearing grade steel retaining pin
Extractor Spring, 5 coil, ASTM Grade A 228 wire stock, stress relieved, Tensile Strength of 393,000 PSI Max, 80 Durometer Per AMS-R-6855 black insert
Extractor Spring O-Ring, Viton (FKM) Fluoropolymer Elastomer
Ejector, S7 shock resistant tool steel alloy, hardened, shot peened per ASTM B851/SAE AMS2430, manganese phosphate
Ejector Spring, ASTM Grade A 228 wire stock, heat treated, stress relieved – Tensile Strength of 376,000 PSI Minimum
Gas Rings, Steel Corrosion Resistant Per AMS 5906 – X3
Carrier machined from 8620 alloy, full auto profile, heat treated, ultrasonically cleaned, hard chrome bore, manganese phosphate – 2 hours accelerated Salt Spray & 48-hour endurance Salt Spray completed on each lot
Gas Key machined from 4130 chromoly steel alloy, heat treated, hard chrome internal & manganese phosphate
Socket Cap Head Screw, steel, grade 4037 per ASTM, heat treated & manganese phosphate 2x
Gas Key is installed with Permatex aviation gasket sealer, torqued to 55-foot pounds, pneumatically steaked and break away tests performed to spec
Cam Pin, precision machined 4340 chromoly steel alloy, heat treated, manganese phosphate & Dry Film Lubricant
Firing Pin, precision machined 8740 steel alloy, heat treated, precision ground & hard chrome plate
Firing Pin Retaining Pin, carbon steel ASTM A510, heat treated & manganese phosphate
The Breek Arms WARHAMMER MOD2 ambi charging handle is a simple and affordable upgrade that will substantially increase the use of your AR-15. Easily grab on either side of the handle and you can quickly charge your rifle even with large gloves with the textured grooves that are cut into the latch handles. The wide set-back latches work great for large optics. The low profile design keeps it slim and sleek looking without sacrificing functionality. Made entirely out of 7075 aluminum for added strength and durability!
The new MOD2 design features improvements for further reducing gas blowback in the shooter’s face. The relief cuts on the top and bottom of the stem are designed to help direct extra gas out the side and away from your face. And for any gas that does manage to go straight back, we increased the height of the shelf to better cover the back of the upper. These modifications help improve the shooting experience, especially when shooting suppressed!
Material: 7075-T6 aluminum
Fits all mil spec AR15/M16 Rifles
Finish: Type III hard-coat anodized
Perfect replacement for any factory charging handle
Latches are also 7075-T6 aluminum
Oversize ambidextrous release levers on both sides, 2.78″ total width across the handles
Set-Back Latches work great for large optics
Allows for one handed manipulation
Higher Rear Shelf and Relief Cuts to Divert Suppressor Gasses
Weighs in just under 1 ounce!
No gun smith required
Made in America
Bookmarks