.40 upper?

[UTShooter71]

Hola,
I have a PSA PX-9, AR9 9mm pistol that is set for Glock mags. PSA does not make a .40 upper and that is what I am looking for. Does anyone know of an upper that will work with the PSA lower?

[lonestardiver]

First question would be does that lower accept .40 cal glock magazines ? I know a .45acp glock pattern lower is supposed to accept 10mm glock magazines. I have that same PSA 9mm lower but only 9mm mags for it.

I do need to get a 10mm mag so I can validate that my .45acp lower accepts them for a 10mm upper. Ugh....then I need to look at .357sig. Again I suspect the .40cal magazine is a profile closer to that of a 9mm. It goes back to the frame/grip size of the glocks to my best knowledge.

[NQNPIII]

Build your own. I did. Regular Aero AR15 upper, Kaw Valley barrel, Kaw valley BCG

[UTShooter71]

NQNPIII,
Does your Aero upper work on a PSA lower?

[NQNPIII]

NQNPIII,
Does your Aero upper work on a PSA lower?

I got in a discussion with a guy the other day. My PSA lower fed 40 into the Aero upper when using the chargin handle. The lower I built for that is a Matrix Aerospace. I put the Matrix on my PSA 9mm upper and it fed a round in the chamber just fine.

Got my barrel, BCG, and forward facing muzzle tip from Joe Bob's. Cut a feed ramp into the barrel with a Dremel and polished it.

PSA's upper is a regular AR15 upper. Compare.

[UTShooter71]

I got in a discussion with a guy the other day. My PSA lower fed 40 into the Aero upper when using the chargin handle. The lower I built for that is a Matrix Aerospace. I put the Matrix on my PSA 9mm upper and it fed a round in the chamber just fine.

Got my barrel, BCG, and forward facing muzzle tip from Joe Bob's. Cut a feed ramp into the barrel with a Dremel and polished it.

PSA's upper is a regular AR15 upper. Compare.

I will compare my PSA upper and lower to one of my AR's. If it is the same I will just build the upper (Joe Bob's has the best prices I have found) for now.

Thanks for the heads up. Any other advice on this build would be appreciated as well.

[UTShooter71]

I just checked and the PSA upper on my PX-9 is just a regular AR upper but with a 9mm barrel. I am ready to build a .40 upper now.

[NQNPIII]

First question would be does that lower accept .40 cal glock magazines ? I know a .45acp glock pattern lower is supposed to accept 10mm glock magazines. I have that same PSA 9mm lower but only 9mm mags for it.

I do need to get a 10mm mag so I can validate that my .45acp lower accepts them for a 10mm upper. Ugh....then I need to look at .357sig. Again I suspect the .40cal magazine is a profile closer to that of a 9mm. It goes back to the frame/grip size of the glocks to my best knowledge.

Glock 40, and 9 mags have the same outside dimensions.

[sburd357]

Hola,
I have a PSA PX-9, AR9 9mm pistol that is set for Glock mags. PSA does not make a .40 upper and that is what I am looking for. Does anyone know of an upper that will work with the PSA lower?

I have a PSA lower (Glock Magazines) that works fine with an upper I built using KVP 40 S&W barrel. These barrels are on sale at Job Bob Outfitters for $80 right now. I mounted it in a $40 slick side Anderson upper and used a $45 Double Star Carbine length float tube.
Utterly reliable using the KVP 40 BCG from Joe Bob's though I always polish the feed cone on Blow Back barrels prior to installation.

If you don't want to build an upper then Stern Defense would be my choice. There BCG should work even better because it is an ounce heavier than the KVP BCG. I added the KAK tungsten weight to my KVP BCG which brings the weight up to 16.5oz and helps mitigate recoil.