Results 1 to 6 of 6

Thread: 700-series carbine extended feedramps?

  1. #1
    Join Date
    Oct 2008
    Location
    Maine
    Posts
    2,156
    Feedback Score
    3 (100%)

    700-series carbine extended feedramps?

    Does anyone have any photos of the earlier style of extended feedramps used in Colt's 700 series carbines (723, 727, 733) in comparison to the current M4 style?

  2. #2
    Join Date
    Jun 2007
    Location
    The Free State of Nebraska
    Posts
    5,441
    Feedback Score
    7 (100%)
    Later 700 series carbines have regular M4 feedramps. 700 series carbines made before about 1990 will have the shallower carbine feed ramps.
    "Not every thing on Earth requires an aftermarket upgrade." demigod/markm

  3. #3
    Join Date
    Oct 2008
    Location
    Maine
    Posts
    2,156
    Feedback Score
    3 (100%)
    When did Colt actually stop production of the 700s? They were produced concurrently with the M4 for at least a few years weren't they?

  4. #4
    Join Date
    Feb 2007
    Location
    Pensacola, FL
    Posts
    1,589
    Feedback Score
    1 (100%)
    Here is a little info that may give you some idea.

    In the early 1980s, at the request of the United States Marine Corps, Colt upgraded the M16A1 rifle, resulting in the M16A2 rifle. Among the major changes were a reinforced lower receiver, a case deflector, a birdcage flash suppressor redesigned to be a muzzle brake, and a barrel with a faster 1-in-7 twist. The faster barrel was necessitated by the switch from the 55 grain M193 bullet to the 62 grain M855 bullet. The M16A2 rifle's barrel was also thicker for the portion in front of the handguard. Colt incorporated these changes into its carbines, which it called M16A2 carbines. The Model 723 M16A2 carbine used the iron sights of the M16A1, but had a case deflector. The barrel had a 1-in-7 twist, but the thinner profile of the older M16A1 carbine's barrel. As with the Model 653, the United States military made small purchases of the Model 723 for its special operation forces.[8] It was notably used by Delta Force operators from the late 1980s to the early 1990s.[9]

    In 1983, Diemaco developed a carbine similar to the Model 723, the C8 carbine for use by the Canadian Forces. The original C8s were built by Colt as the Model 725. In 1984, the U.S. government asked Colt to develop a carbine with maximum commonality with the issue M16A2. Colt named the carbine as the XM4. The project would eventually culminate in the development and official adoption of the M4 carbine in 1994.


    Though Colt has focused its attention on carbines with 14.5-inch (370 mm) barrels and rifles with 20-inch (510 mm) barrels, Colt continues to make carbines with 11.5 inches (290 mm) barrels, which it calls Commandos. Originally, Commandos were assembled from whatever spare parts are available, so Model 733 Commandos could have A1-style upper receivers with case deflectors or A2-style upper receivers, and M16A1-profile 1:7 or M16A2-profile 1:7 barrels. Depending on the specific models, Commandos may have had three-position fire control groups (safe/semi-automatic/three-round burst), or four-position having both full-automatic and burst. The modern Model 933 has a "flattop" receiver, with a removable carrying handle and a MIL-STD-1913 Picatinny rail, with semi-automatic and automatic fire. The Model 935 Commando has the features of the Model 933, but has three-round burst fire instead of automatic. Though originally called the M16A2 Commando, Colt now markets them as the M4 Commando.

    The production on the Model 733 may have ended about the same time as the Model 723 and 727 or maybe up to a couple years afterwards.
    "A Bad Day At The Range Is Better Than A Great Day Working"

    USMC Force Recon 1978-1984
    US Air Force Res. 1995-2004 (Air Transportation)
    M16/AR15 shooter since 1978, gun collector and AR builder since 2004

  5. #5
    Join Date
    Jun 2007
    Location
    The Free State of Nebraska
    Posts
    5,441
    Feedback Score
    7 (100%)
    Quote Originally Posted by Circle_10 View Post
    When did Colt actually stop production of the 700s? They were produced concurrently with the M4 for at least a few years weren't they?
    The 700 series was made up until the early 2000s.

    The most recent one I have seen is a 2002 made 727.
    "Not every thing on Earth requires an aftermarket upgrade." demigod/markm

  6. #6
    Join Date
    Oct 2008
    Location
    Maine
    Posts
    2,156
    Feedback Score
    3 (100%)
    . In 1983, Diemaco developed a carbine similar to the Model 723, the C8 carbine for use by the Canadian Forces. The original C8s were built by Colt as the Model 725.
    A C8 style carbine was actually going to be my first Retro build way back when. I even had a lightweight 14.5" CHF barrel with the C8 style .750 gas block journal. But plans ended up changing.

    Maybe it's because I'm nostalgic for the 80's and 90's when I was a kid, but the 700 series carbines are my favorite variants.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •