Results 1 to 7 of 7

Thread: Midwest Industries NEW Non QD Optic Mounts

  1. #1
    Join Date
    Jun 2006
    Location
    Waukesha WI
    Posts
    749
    Feedback Score
    1 (100%)

    Midwest Industries NEW Non QD Optic Mounts

    Looking to mount your Trijicon MRO, Aimpoint micro, or one of the many red dots that attach using the Aimpoint mounting interface?

    If you do not plan on taking the sight on and off frequently be sure to consider our new non QD optic mounts.

    These mounts are designed to provide a snag free, clean looking, and strong mounting option that is made in the USA.

    These mounts are machined from billet 6061 aluminum and are hard-coat anodized. They attach with two socket head cap screws which thread into stainless helicoils for added strength.

    Our Trijicon MRO mounts are available in both lower 1/3 as well as absolute co-witness.

    Our Aimpoint micro mounts are available in lower 1/3, absolute co-witness and a NV height which has a window allowing access to your iron sights.

    All of the mounts have an introductory price of $64.95 with the exception of the NV height which is being introduced at $79.95









    https://www.midwestindustriesinc.com...-MRO-s/582.htm

  2. #2
    Join Date
    Oct 2010
    Location
    Northern Colorado
    Posts
    5,167
    Feedback Score
    60 (100%)
    The window for BUIS is genius.

  3. #3
    Join Date
    Jul 2015
    Location
    America
    Posts
    124
    Feedback Score
    4 (100%)
    You guys should make a 1.93 mount for the aimpoint PRO. If you guys do that please make sure you leave a cut out in the mount so that irons can be seen.
    Last edited by Giggles; 03-13-20 at 15:17.

  4. #4
    Join Date
    Jan 2011
    Posts
    106
    Feedback Score
    2 (100%)
    1.7 height 30/34mm mount please

    Think Badger is the only one doing it ATM? Be nice for more options.

  5. #5
    Join Date
    Jun 2006
    Location
    Waukesha WI
    Posts
    749
    Feedback Score
    1 (100%)
    Quote Originally Posted by LowSpeed_HighDrag View Post
    The window for BUIS is genius.
    We did this to allow the use of the rear sight in two places .If you dont run a magnifier run it in the normal spot for a full sight radius. If you do run it in the shown position. We have found most LE guys dont run magnifiers as they arent shooting over 100 yards .

    thanks

    Troy

    MI

  6. #6
    Join Date
    Oct 2014
    Posts
    928
    Feedback Score
    3 (100%)
    Is the MI solid one-piece mount stronger than the Trijicon non-QD MRO mounts?

    Also, no mention of threadlocker on the website. Is the direction to not use it on either the optic-to-mount screws or the crossbolts?
    Last edited by grizzlyblake; 03-16-20 at 13:53.

  7. #7
    Join Date
    Jun 2006
    Location
    Waukesha WI
    Posts
    749
    Feedback Score
    1 (100%)
    Quote Originally Posted by grizzlyblake View Post
    Is the MI solid one-piece mount stronger than the Trijicon non-QD MRO mounts?

    Also, no mention of threadlocker on the website. Is the direction to not use it on either the optic-to-mount screws or the crossbolts?
    I can say with total confidence our mounts are very strong . I am not getting into the Stronger than this and that route. We do not use loctite on screws that thread into a Locking Helicoil. You could pull the heli coil out of the mount if you ever wanted to remove the mount . We have never had one loosen. If your concerned mark it with a paint marker to make sure your screw isnt loosening. We have never used loc tite on the scope cross bolts either . If the instructions are followed we highly doubt you will ever have a issue.
    thanks

    Troy

    MI

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •