Looking for Dillon 550c upgrades

[CrowCommand]

Just picked up a 550C to load 45ACP, 9mm, .223, and maybe more later on.

Going to set it up today, but just wondering what the consensus is on must have upgrades?

I've got an RCBS single stage and a Lyman turret for more precise loading, I got the Dillon to crank out blaster rounds en masse.

This is my first progressive press, any advice is welcome.

[drtywk]

Upgrade to the 650/750. they are vastly superior, in my opinion, to the 550 due to them being auto indexing and having a case feeder. You can get a case feeder for the 550, but you can't run rifle brass in it.

[CEE]

I started reloading years ago on a 550B, & they have added some great options over the years. I only added the strong mount to my setup but have considered the roller handle, bullet tray & low-powder sensor. The strong mount is the best addition in my mind which is why I added it couple of years ago, the others are more to individual taste.

[markm]

The strong mount is the best addition in my mind which is why I added it couple of years ago, the others are more to individual taste.

Agreed. I too run the 550b. The only downside is the priming system is complete trash. I prime off press.

Being a Type A control freak, I prefer the manual indexing on the 550.

[chamber143]

Upgrade to the 650/750. they are vastly superior, in my opinion, to the 550 due to them being auto indexing and having a case feeder. You can get a case feeder for the 550, but you can't run rifle brass in it.

i would have to agree but i think he just bought the 550. It is still a great press. Only problem with the 750 is that is so easy to get flying through the reloads that you can miss something and not notice. I came from a lee 4 spot turret press and i never had one single issue at all. Since i got the 750 i have had a couple ftf due to not charging a round. I know its my fault and i need to pay better attention, its just so damn easy to simply pull the handle and not focus. So i have had to learn to pay closer attention. Training scars suck but are a necessity of screwing up.

[andre3k]

Go for additional lighting whether its on the press or your bench area. That has always been a welcome upgrade. All of my presses get LED light kits.

[CrowCommand]

Thanks for the responses...I picked the 550 for the manual indexing, really. I want to keep an eye on things, this being my first progressive press. I will probably upgrade in the future.

The mount from inline fab was one of the first things l was looking into, the LEDs were also on the list.

Interested to here more about the priming system, @markm. I was looking forward to an "all in one" package, but nothings perfect I suppose.

[Bimmer]

Going to set it up today, but just wondering what the consensus is on must have upgrades?

I have one of the roller bearing kits that fits under the shell plate... I'm not sure it's a huge improvement, but it makes sense to have a bearing there, rather than simply having the shell plate dragging along.

The only downside is the priming system is complete trash...

I don't get it... I've been priming with my RL550B for decades, and I've hardly ever had any problem with the priming system.

I picked the 550 for the manual indexing, really.

Good call... Manual indexing is a bit slower, but if you mess up automatic indexing, then you have a helluva mess.

[Coal Dragger]

Only “mandatory” upgrade is the Inline Fabrication mount of your choice, makes a big difference in flex free operation and of course getting the press at your preferred working height.

[Bimmer]

For now I will take the advice of just running it stock until I have a better idea of where it needs tweaking.

This is a wise course of action...

Only “mandatory” upgrade is the Inline Fabrication mount of your choice, makes a big difference in flex free operation and of course getting the press at your preferred working height.

Hmmm... I bolted my 550 to a homemade bench. The benchtop is two sheets of 3/4" plywood. It doesn't flex at all.

As for height, I built the bench at about my preferred working height, and I sit on a height-adjustable stool... Perfect.