Can it be done legally, without a s/n? Probably the dumbest question you've heard all day, I know.
Can it be done legally, without a s/n? Probably the dumbest question you've heard all day, I know.
If it's completely unmachined, yes. Once it's been so much as kissed by a drill-bit the Rubicon is crossed; until then it's just a hunk of metal or plastic.
<><><><><><><><><><><><><><><><><><><><><><><><>YOU IDIOTS! I WROTE 1984 AS A WARNING, NOT A HOW-TO MANUAL!--Orwell's ghost
Psalms 109:8, 43:1
LIFE MEMBER - NRA & SAF; FPC MEMBER Not employed or sponsored by any manufacturer, distributor or retailer.
I am going to disagree as 80% lowers are not considered the firearm, so why would it matter if you did anything to that 80% lower? If you owned a 80% lower that you finished, you are also able to sell it as well. As long as you are not buying 80% lowers to finish so you can resell them.
If it is "80 percent" it is legally a lump of aluminum (or polymer). If any steps to complete beyond that have been performed you start sailing uncharted waters. I am not aware of any clearly defined boundary line in terms of law or regulation. Logically any degree short of completed would be incomplete and therefore not a firearm. But logic has very little to do with it.
Go Ukraine! Piss on the Russian dead.
I know Pennsylvania made 80% lowers a “firearm,” a couple years ago, but an injunction stopped it, temporarily. While federal law currently doesn’t consider them firearms, state laws may be different.
The problem with making an 80% receiver a "firearm" is define, legally, what a 80% of a receiver is. Then I just do 79% and voilà., I'm all legal again with a hunk of steel or aluminum.
And, if you engrave a serial number, your company's name on a random gun-shaped piece of aluminum, it doesn't make it a firearm, but engraving the outlines of pin holes apparently is.
Unfortunately, no. There is no legal definition of “80%,” it’s just a made up marketing term. ATF deemed 80% lowers a “non-firearm,” is all, no “80% percent.” Percent completion doesn’t legally exist. The push from the Antis is to make any “readily converted” easily machined with CNC tech a firearm. Spare parts, too. So, kits & “80%” marketing goes away.
Idiotic? Absolutely. Capricious? Correct. A 3/4” nipple can be made into a 12 gauge zip gun & a .25” nipple is a .22LR, so where does the lunacy end? With CNC CAD/CAM, a block of aluminum is a potential receiver. When the laws were made, CNC didn’t exist, so running a vertical mill was beyond the average gun owner to machine lowers.
It’s akin to the retarded plan of “armor piercing bullets” being redefined as “any projectile that can defeat soft body armor,” which includes all FMJ going over 2,000 fps, like most high power rifle FMJ.
I don’t agree with any of it—it’s just what the ATF claims & the antis have gun kits & spare parts in their sights; Biden will deliver. Don’t be surprised if proof of legal ownership is required for spare parts in the future.....
I know this is an old post but you can ship/sell a 80%Lower to anyone and anywhere as long as the state your shipping to laws also allow them to have an 80%Lower. Also it does not matter at all if you have already started the process of working on it for example (you bought a 80%Lower it finally shows up and before you even put the jig on your looking at it and decide you don’t have the time to do it then it’s still a new 80% and can be re sold and shipped to buyer or say you have already put the jig on the lower and drilled the pre holes on the top you know all the tiny holes some new step that some ppl do well say you did that part and said this is already too much and you stop and want to sell it well it has already been worked on but you haven’t finished it yet so it’s not a firearm not even close it just has a bunch of holes at the top that’s it so I can buy it from you and you can mail it to me legally and not have to worry about anything) so yes you can ship a 80%Lower hope this helps you out
Sent from my iPhone using Tapatalk
Bookmarks