-
300BLK SBR Setup and Q re: muzzle device
Edits below (after original post with muzzle device question) as upper is accessorized and tested with different lower setups.
Original post:
OK, I need to pick a Keymo muzzle device for a 300 BLK upper. This is a 7” barrel, so a little shorter than optimum, so I assume there will be some unburnt powder to blast the interior of a suppressor.
I wanted to focus this on “small,” assuming suppressed if using indoors for HD. KeyMicro brake seems like the easy option, it’s small and should (?) provide a small sacrificial baffle effect. This would be the only brake I have any more, as flash hiders just seem like a better idea all around, particularly with short barrels. Length/weight (size) and protection of suppressor are what I had prioritized.
However, KeyMicro brakes seem out of stock most places, so I figured I’d get general opinions.
Dead Air standard brake
*I thought about cutting the third baffle off this, seems like that would end up as a decent compromise.
Dead Air standard flash hider
*General good option, but lose any protection of suppressor while gaining flash diffusion. I’m not opposed to this, unless it would cause more wear than a brake, and I think it would.
SOLGW NOX
*Not considering. Extra size, and I’ve repeatedly read that it pushes down more than needed. No protection benefits at a higher cost than a standard Dead Air option.
Lantac
https://www.lantac-usa.com/product-p...-brake7-62-308
*Expensive. It almost looks like it has a flash hider after the brakes… Anyone have experience?
FCD 6310KM
https://www.forwardcontrolsdesign.co...x24_p_192.html
*I have one or two of these on hand. Comps a bit, good flash suppression. Does it protect the suppressor at all, or at least compared to a standard Dead Air flash hider?
Experience, other options?
Update on setup, still haven’t changed the muzzle device. 7/16/2022
Factory BCM 7” 300BLK barrel with 5” MCMR
Holosun 509T on Reptilia 1.93
Surefire X300U-B
Radian Raptor
BCM foregrip
Before adding the extras, I got one measurement with a pistol lower. I then got more with an SBR’d A5 lower. Note that the A5 with B5 Bravo is notably “longer” due to not closing
Weight with upper set up per above plus SBR A5: 6lb 4.2oz
Length with fully collapsed SBA3 on standard carbine receiver extension
Comments:
The difference in length between A5/B5 Bravo and standard/SBA3 is irrelevant to me, as the A5 position two is “right.” The SBA3 pulled out a bit ends up the same. So I lose some compactness for storage, but not much. In use, both are good.
Weight is well balanced, which may change with a suppressor.
As light as it is, I intentionally placed the 509T further to the rear than usual to shift the balance point. With the 1.93 mount, it works better than I expected; picking up the dot is super easy. I actually left the Eotech style circle dot on, as it seems to work well for me.
Next steps will be changing to Keymo muzzle device to go with a Rex Silentium MG7K .308 suppressor, recently arrived at my local FFL. I’m going to play around with the foregrip. I’m thinking I will keep it, as it feels “right” and also lines up well to activate the light.
I have a couple options for a different charging handle (Badger, Raptor SD, Q Raptor SL), but not moving anything around until I see how it works as is with the MG7K.
Last edited by JediGuy; 07-16-22 at 18:19.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Bookmarks