Hey Doc, I know the 10mm is a bit outdated, but I'm still a fan of the round and if there is any 10mm testing data available, I'd be grateful if you could point me in the right direction.
Thanks,
USSA-1
Hey Doc, I know the 10mm is a bit outdated, but I'm still a fan of the round and if there is any 10mm testing data available, I'd be grateful if you could point me in the right direction.
Thanks,
USSA-1
Occupo Mens- Win the Fight
United States Shooting Academy
Sorry, but we have not tested any 10 mm loads in over a decade. It is unfortunate, since 10 mm is one of the best SMG loads ever produced.
If that's an offer, I'll start to beg, borrow, or steal some ammuntion for you to test.
USSA-1
Last edited by USSA-1; 01-29-09 at 15:29.
Occupo Mens- Win the Fight
United States Shooting Academy
Double Tap 10mm Data
All of these tests were done using 10% ballistic gelatin provided by Vyse gelatin using all FBI protocols and 4 layers of denim and two layers of light cotton T-shirt in front of the gelatin.
DoubleTap 10mm
135gr JHP @ 1600fps - 11.0" / .70" frag nasty
155gr Gold Dot JHP @ 1475fps - 13.5" / .88"
165gr Gold Dot JHP @ 1400fps - 14.25" / 1.02"
165gr Golden Saber JHP @ 1425fps - 14.75" / .82"
180gr Golden Saber JHP @ 1330fps - 16.0" / .85"
180gr Gold Dot JHP @ 1300fps - 15.25" / .96"
200gr XTP @ 1250fps - 19.5" / .72"
230gr Equalizer @ 1040fps - 11.0" and 17.0" / .62" and .40"
Here is the link
http://www.ar15armory.com/forums/Dou...Data-f268.html
No data, but here's what the Bureau is still issuing for the MP5/10s.
Outdated? How about incredibly effective but misunderstood?
10mm Tech Notes
10mm Commercially Available Factory Loads
10mm Auto Cartridge
10mmtalk.com
IMO, one of the nicest looking 10mm's around is Ken Lunde's Colt Delta Elite 10mm
Last edited by zippygaloo; 01-30-09 at 01:16.
I am a bit skeptical about the Double Tap ammo test results...
On the other hand, we have tested the ammo that "Federale" depicted--it has been a quite a while, but IIRC, out of a Colt Delta Elite it ran about 925 fps, penetrated in the 16" range with expansion around 60-62 caliber, with minimal changes against 4 layer denim and auto glass. A relatively mild, but good performing load.
Last edited by DocGKR; 01-29-09 at 19:19.
Doc, what is your opinion of the 10mm for use on auto bodies? What load would you recommend for use in, around and against automobiles? Planning on hard mounting a G20. I've seen what .357 Sig does on steel but don't like that cartridge, I was thinking that a 180 at 1300 might do well.
Thanks in advance!
Again, we have not tested 10 mm loads in over a decade, however, the Federal 190gr JHP (XM1003A) shown above is a good choice as the bonded bullet does well against intermediate barriers.
Link http://www.doubletapammo.com/php/cat...products_id=39
When penetration is key, two holes bleed better than one! Entrance and exit hole! This is an excellent load for woods protection.
Caliber : 10mm
Bullet : 200gr FMJ / FP
Ballistics : 1275fps / 722 ft./lbs. - Glock 20
Glock 29 - 1225fps
Box of 50rds.
Last edited by sjc3081; 01-30-09 at 05:20.
Bookmarks