Page 2 of 2 FirstFirst 12
Results 11 to 19 of 19

Thread: Ever wear out a barrel?

  1. #11
    Join Date
    Jan 2008
    Location
    AZ-Waging jihad against crappy AR's.
    Posts
    24,902
    Feedback Score
    104 (100%)
    Just an FYI. The military gage differs significantly in design from that gage. I don't know how much I would trust that specific gage to get an accurate reading.

    Quote Originally Posted by emt370 View Post
    This gauge will help you see the throat erosion. Basically, when you fire a round, hot gases escape around the bullet as it leaves the casing and that effectively makes a larger chamber in which the round will sit. With that gauge, the farther it goes into the barrel when compared to new, the more erosion is present and the more worn the barrel is. Head spacing deals with how far the round will chamber. As the barrel and bolt wear, the round will seat deeper and there will be more room for it to move or expand as it is fired. This also is not desirable as the casing becomes less supported.



    Owner/Instructor at Semper Paratus Arms

    Facebook: https://www.facebook.com/SemperParatusArms/

    Semper Paratus Arms AR15 Armorer Course http://www.semperparatusarms.com/cou...-registration/

    M4C Misc. Training and Course Announcements- http://www.m4carbine.net/forumdisplay.php?f=141

    Master Armorer/R&D at SIONICS Weapon Systems- http://sionicsweaponsystems.com

  2. #12
    Join Date
    Mar 2007
    Posts
    2,036
    Feedback Score
    1 (100%)
    Ok, two cents on this:

    Over the years I have seen 100 or more bbls wear out on .mil guns.

    In my experience the throat erosion gauge is not a very accurate tool. Throat erosion in the M4 usually occurs 1-3 inches past the case mouth. The tool does not go deep enough.

    In you average M4, you will detect bore wear long before you detect throat erosion. Even though the throat may be ruined and you accuracy is crap.

    IMO, the best way to detect a worn bbl is to reconfirm your zero from time to time. When you see your shot group open up and you know you are doing your part, it is a good indication that your bbl is getting shot out. Depending on your duty cycle this will happen around 10-20k rounds.

  3. #13
    Join Date
    Oct 2009
    Posts
    31
    Feedback Score
    1 (100%)
    Won’t the rifling be worn out? What’s the barrel life for semi autos?

  4. #14
    Join Date
    Jun 2006
    Location
    NoVA
    Posts
    10,780
    Feedback Score
    17 (100%)
    The throat erodes much faster than the headspace.

    I usually replace a barrel when it will no longer group well at 100yds even after a good copper cleaning and crown cleaning. This means while freefloated and to me well means less than 5MOA (if using a red dot sight, chrome lined barrels) or 2MOA if using magnified optics (usually stainless or non-chrome lined match grade barrels). These always still headspace just fine.
    Chief Armorer for Elite Shooting Sports in Manassas VA
    Chief Armorer for Corp Arms (FFL 07-08/SOT 02)

  5. #15
    Join Date
    Jan 2009
    Location
    Northern NY
    Posts
    730
    Feedback Score
    14 (100%)
    Quote Originally Posted by Armati View Post
    Ok, two cents on this:

    Over the years I have seen 100 or more bbls wear out on .mil guns.

    In my experience the throat erosion gauge is not a very accurate tool. Throat erosion in the M4 usually occurs 1-3 inches past the case mouth. The tool does not go deep enough.

    In you average M4, you will detect bore wear long before you detect throat erosion. Even though the throat may be ruined and you accuracy is crap.

    IMO, the best way to detect a worn bbl is to reconfirm your zero from time to time. When you see your shot group open up and you know you are doing your part, it is a good indication that your bbl is getting shot out. Depending on your duty cycle this will happen around 10-20k rounds.
    I happened to escort the Small Arm Lead at the DCD from the Infantry center into my old arms room a few years ago. We had been talking about many issues with weapons systems and one that we happend to be discussing was service life of the M-4. At the time our Infantry BN's had been running around 9,000 rounds a year through their carbines in training. We had been doing so for at least 5 years, this was in 2005 or so. We grabbed three random rifles off the racks and looked them over. What stood out right away was that the rifling was only faintly visable in the barrels. This from a arms room of 100+ rifles.

    We called the TACOM LAR down after. He gaged the whole rack for each of the rifles that we spot checked with the trusty throat erosion gauge. All the weapons passed so they had to be good to go. Lands and Grooves are not a inspection requirement.

    It's a measure, but I'm not so sure it's a good one. There are other ways you can get a barrel to be coded out, but very few Infantry units are resoursed to do it time wise. I'm not sure how this is being addressed now when the SARET Teams TI weapons during Re-Set.
    pro-patria.us

  6. #16
    Join Date
    Jan 2008
    Location
    AZ-Waging jihad against crappy AR's.
    Posts
    24,902
    Feedback Score
    104 (100%)
    My guess is that it isn't being addressed. This also came up during the Colt course that I just attended and the instructor was in the opinion that when your groups start opening up, then it's time to change the barrel out.

    Maybe a better question to ask is; How much accuracy do you need? If you say that you need to be able to hit a man size target at 300M and your groups were tight and now they have opened up to 5" or 6" inches can you live with that? I think I could. To others that may be unacceptable.

    Quote Originally Posted by DMR View Post
    I happened to escort the Small Arm Lead at the DCD from the Infantry center into my old arms room a few years ago. We had been talking about many issues with weapons systems and one that we happend to be discussing was service life of the M-4. At the time our Infantry BN's had been running around 9,000 rounds a year through their carbines in training. We had been doing so for at least 5 years, this was in 2005 or so. We grabbed three random rifles off the racks and looked them over. What stood out right away was that the rifling was only faintly visable in the barrels. This from a arms room of 100+ rifles.

    We called the TACOM LAR down after. He gaged the whole rack for each of the rifles that we spot checked with the trusty throat erosion gauge. All the weapons passed so they had to be good to go. Lands and Grooves are not a inspection requirement.

    It's a measure, but I'm not so sure it's a good one. There are other ways you can get a barrel to be coded out, but very few Infantry units are resoursed to do it time wise. I'm not sure how this is being addressed now when the SARET Teams TI weapons during Re-Set.



    Owner/Instructor at Semper Paratus Arms

    Facebook: https://www.facebook.com/SemperParatusArms/

    Semper Paratus Arms AR15 Armorer Course http://www.semperparatusarms.com/cou...-registration/

    M4C Misc. Training and Course Announcements- http://www.m4carbine.net/forumdisplay.php?f=141

    Master Armorer/R&D at SIONICS Weapon Systems- http://sionicsweaponsystems.com

  7. #17
    Join Date
    Jan 2009
    Location
    Northern NY
    Posts
    730
    Feedback Score
    14 (100%)
    I should have been clearer. In most units the only grouping a soldier ever see's are those fired at 25 meters zeroing or doing alt C qualification. Spotting a group opening up at that range is just about impossible. Adding to theissue it is not uncommon for soldiers to change weapons, in garrasion, often. This means it is hard to see changes in a weapons performance over time(and most soldiers would not notice the differance anyhow).

    One way you can get a barrel coded out is if the rounds are keyholing. At 25 meters this can be quite a feat to spot in all but the worst barrels. On the Army qual ranges you only have to hit the target round placement does not count. You don't go down range to see if your rounds are keyholing. Even if you did the targets are so full of holes you could never say if one was yours.

    Even for the odd unit thatpulls targets on a KD range keyholing will often be overlooked. It is not something taught as a symptom to look for. For that matter there are a host of issues you could go into about lack knowledge at the small unit leaders level on weapons and marksmanship training.
    pro-patria.us

  8. #18
    Join Date
    Sep 2007
    Location
    Kentucky
    Posts
    27
    Feedback Score
    0

    Wink

    I've had M4 barrels that needed to be replaced, as identified during semi-annual weapons gauging. I believe an M4 barrel is rated for about 7,000 rounds-as we all know a lot depends on how fast those rounds were fired.

    But, in the case above, the Colt M4's were issued brand new in the box, and during the semi-annual gauging a number of them needed to be replaced about 6 months later. I did not dig into the amount of throat erosion due to time concerns, but 7,000-10,000 or more rounds sounds about right.

  9. #19
    Join Date
    Nov 2007
    Posts
    11,063
    Feedback Score
    41 (98%)
    Military guns are going to be run harder than your average civilian gun.


    The most important issue from what I have gathered is how the barrel is shot. An easy 200rds over 10 months is going to show far less wear than a barrel shot 2k rounds in a single day.


    Military standard issue cleaning rod is non-coated steel.


    M855 is hotter ammunition than your average 223 load.


    Ive seen M249's get a few thousand rounds put through them in under an hour, and barrels at night bright red hot.


    I also have one stainless barreled gun that has about 6k rounds through it in a couple of years, and it still shoots sub-moa quite easily with good ammo. I used to have another one with about 4k rounds that was shot a lot harder, and went from sub-moa to 1.5-2moa pretty quick.


    This past weekend I also managed to turn my Triple Tap brake colors because I got it so hot...wanted to put it through its paces....haha


    Key-holing and loss of accuracy are the two biggest indicators to look for, however.

Page 2 of 2 FirstFirst 12

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •