thinking about an Aimpoint Micro H1, have a few questions

[lebowski]

Thanks for the input guys.

Ended up going for (well ... asking for xmas so we'll see) the CompC3 + American Defense package from Grants. Seems like too good a deal to pass up. Chose the High mount (lower 1/3) and 2MOA dot (that's all he has in stock ... but I think that's what I'd prefer anyway).

Thanks a lot for the help. I realize most of this has been covered before and I did use the search feature, but it helps to have some hand holding on a decision like this.

[SeriousStudent]

Nice choice. That was what I bought, and where I bought it from.

Very fast and easy to use. Plus, if you wish to add a Aimpoint 3x magnifier, it drops right in behind it.

[steve-oh]

Good choice, can't go wrong. Also... stay out of Malibu, Lebowski.

[lebowski]

Thanks for the help, guys.

My dad ordered me the CompC3 with mount package from G&R for xmas (I got him a Beretta 92FS), and I'm not sure if Grant was out of stock of the C3 or what, but he upgraded me to the ML3 w/ mount for no extra charge. Pretty good deal! I haven't taken it to the range yet (hopefully this week), but it looks like a great setup. I'm looking forward to shooting it.

[sundance435]

Does the rubber cover for the M/ML series fit on the C3?

[Alaskapopo]

I'm about ready to mount an optic to my DDM4. I've had the gun for about 6 months (first and only AR) and I've been using just the irons thus far, wanted to learn the basics w/ irons before moving forward.

Ideally, I'd like this gun to be a CQB to ~200m gun. I just use it for plinking now, but it could eventually replace my 870 as my bedside/HD gun. I have a white light (Streamlight TLR-1) mounted on the rail, but that is and will remain the only accessory other than the optic and the vertical foregrip that came on the DDM4 (I'd like to keep it clean, simple, and lightweight). I plan to run the optic in conjunction with the irons that came on the DDM4.


First question - what do you guys think of my choice of the Micro H1 for this role? How fast is target acquisition of the Micro line of Aimpoints? Is there anything else I should be considering? Do the larger Aimpoints (ML3? C3?) have faster target acquisition or other benefits that I'm missing?


My primary questions concern mounting the optic:

I have the iron sights that came on the DDM4 (not the flip up variety, they are permanently up both front and rear). I'm guessing the ideal setup is to have the irons co-witness on the bottom 1/3 of the optic? Is this thinking correct? The Aimpoint Micros look pretty small, and I haven't handled them in person, so I was wondering if it isn't so small that the irons disrupt the sight picture through the optic?

Assuming this setup (bottom 1/3 co-witness), what mount should I use? Ideally, I'd like QD. Are the Larue QD mounts adjustable so you can adjust where the irons co-witness within the optic, or is it a fixed location?

Finally - where's the best place to buy Aimpoint optics (and larue? mounts) now to get the best deal?

I think the Aimpoint T1 or H1 is an excellent choice for what you want. I like my T1. I use it as a primary optic inside of 25 yards and my ACOG TA33 as my primary past that. You could do just fine however with just the Aimpoint.
Pat

[Schuey2002]

Does the rubber cover for the M/ML series fit on the C3?

Yes, it will...

[RUSKI]

It seems like you are set on the Aimpoints.
I have run a Vortex Strikefire aimpoint knockoff w/ high mount, and a EOTech 552 on my build. I was able to get a lower 1/3 co witness with the Vortex, and a near center co witness with my 552. My irons are a YHM front flip up gas block and MI rear flip up. My sight picture was far better with the EOTech co witness. The housing on the Vortex restricted my view quit a bit.
Just something to consider.