Shotgun pic thread

[Wake27]

- 26" barrel shortened to 18-3/4 inches and re-installed the RemChokes
- HiViz CompSight PM1002 - Competition Shotgun Sight (same as used on the 1100 Tac4)
- Cut the stock down to 13” LOP and re-installed the original Remington butt pad
- Choate 2-shot magazine extension
- Brownells stainless steel magazine follower (front of spring as a tube retainer)
- G,G&G stainless steel magazine follower (rear of spring)
- Wolff Extra Power Magazine Spring
- Dave’s Metal Works Easyloader
- Vang Comp dome button safety
- G,G&G QD Rear Sling Attachment
- CDM Gear BMT with 3-slot rail (right side) and QD Sling Attachment on left side
- Vickers Combat Applications Sling
- Surefire X300 light (installed when needed)

Damn that's sick...

[Cokeman]

That does look good. It makes me want to put wood on mine.

[USMC_0317_SS]

Here is my Remington 870 I posted previously and got alot of comments on. Well, I have upgraded it once again. I personally custom Cerakoted all of the components and even coated my HK USP .40C to match...well all of my firearms are FDE & Black...lol.

P.S,
It's 11 lbs. fully loaded.




Details:
Remington 870 18.5" Tactical Smooth Bore (Ceracoted FDE / Bolt & Pump Cerakoted Grahpite Black)
Remington Arms (3) Round Magazine Extension Tube w/ Tactical Follower (Cerakoted FDE)
Rhino Rail System
Mesa Tactical High Tube Adaptor (Cerakoted FDE)
Mesa Tactical Side Saddle
Surefire M951XM07
EoTech 552.65A (Hood CeraKoted FDE)
Magpul UBR Stock FDE
Magpul UBR Metal Strike Plate
Magpul UBR Upgraded Recoil Pad
Magpul MOE Grip FDE
Magpul AFG-II FDE
Magpul FDE MBUS (Fron & Rear)
Falcon Industries Ladder Rail Covers (FDE)...
....and as always rocking the 9 pellet 00 Buck Shot !!!



Here is an 870 Express 28" I have had since I was 14. This shotgun is almost 20 years old and has bounced around the "duck-boat" every year for 18+ years. I stripped it down (what was left of the original factory finish) and recoated the barrel and receiver in Cerakote's "Burnt Bronze" / bolt in "Graphite Black". After refinishing I replaced the beat-up, old wood furniture with the Magpul SGA & MOE furniture in black and tossed on a "Tru-Glow" fiber optic front bead sight. No more rust and a lot lighter.

[Canonshooter]

Damn that's sick...

Thanks!

I had a Speedfeed youth stock on this SG for a long time, which I very much liked. However, the matt black stock/polished blue metal combo always irked me and several times I was going to have the metal bead blasted and reblued. Though the Speedfeed stock is easier to grip and hold on to, I'm glad I had the original stock shortened (same LOP as the Speedfeed) and went that route instead.

This 11-87 cycles the Federal LE/PD132 "reduced recoil" load (00 buck, 9 pellets at 1145 fps) perfectly and shoots the full power Federal P127RS one ounce slugs to POA at 50 yards into 3 inch groups. These are my go-to loads for this gun. This is a pressure compensated barrel, so 3-inch loads can be used too (though I have no practical use for them in this gun).

Interestingly, with a barrel seal activator installed, it will also cycle the lighter LE133 loads (8 pellets at 1145 fps). Even though they have been 100% reliable, they do not cycle the action as briskly therefore I would not use them for a HD application. Since the LE/PD132 loads work perfectly and are very comfortable to shoot, there's really no need for the 8-pellet load anyway so I run the SG without the activator.

Thanks for taking a look and commenting!

[FAB45]

Mossberg 500

[K Town]

[Cutshaw]

[MFWIC2]

S-12 8" SBS ROCK's with a MD20 drum. Kel-Tec doesn't have s**t on this gun.

Attachment 13955

[PieceKeeper]

[Evergreen]

S-12 8" SBS ROCK's with a MD20 drum. Kel-Tec doesn't have s**t on this gun.

Attachment 13955

PURE AWESOMENESS!! I cannot even begin to tell you how jealous I am of you. And , to add salt to the wounds, I live in the state of Washington, where it isn't even legal to own that gun (due to barrel length).