base and rings

[kluxman45]

id like a set of badger nightforce seekins ect.something with 3 screws on each sideof rings..only i dont need a 20 moa.dont they make aregularbase platefor a remmy700?night force says its gotta be a night force or upper end base

[Jim D]

id like a set of badger nightforce seekins ect.something with 3 screws on each sideof rings..only i dont need a 20 moa.dont they make aregularbase platefor a remmy700?night force says its gotta be a night force or upper end base

Why is 3 screws a must?

These are some of the best made rings I could find, the bases have a good rep, too. http://egw-guns.com/store/index.php?...roducts_id=180

Knowing how EGW makes parts, I'd put them up against anyone in the industry.

http://egw-guns.com/store/index.php?...roducts_id=220

[Triad Tactical]

RE Badger Ordnance:
You only need the six screw if you are shooting a heavy magnum or need to replace the front top cap to hold a NV device etc.

You dont mention what size scope you have so I cant tell you which ring set you would need but here are the basics:

40mm obj=306-08 .823" tall
50mm obj=306-20 .885" tall
56mm obj=306-21 1.0" tall

They also make a flat/zero cant base, 306-06F

I sell a lot of these rings and bases and try to keep them in stock.

[kluxman45]

its a night force bench rest 8x32x56 going on a 700 mil specrifle.thank you

[kluxman45]

how much are your rings and base plate for the remington 700 mil spec? you have a siteto go to?

[CoryCop25]

I have an EGW base and Burris mid, rings (3 Screws) on my 700 SPS.

[kluxman45]

I have an EGW base and Burris mid, rings (3 Screws) on my 700 SPS.

wheres there rings at?egw.id like to keep them all one manurfacture.with real close tolerancesso i dont have to bed the base

[TacticalIntervention]

Folks, no need for more than four total screws on a single ring unless you have a Simrad Cap.

My favorite rings are the Nightforce Ultra Lights.

Badger is favorite base.

That combo has served me very well.

[kluxman45]

Folks, no need for more than four total screws on a single ring unless you have a Simrad Cap.

My favorite rings are the Nightforce Ultra Lights.

Badger is favorite base.

That combo has served me very well.

do you think on a remington 700 milspec 5r rifle{a new one}i ll have to bed the base plate?plus i dont need a 20 moa,im shooting at 100 200 300 yrds.thats it.i dont think badger makes a 0 moa do they?havent seen one.egw does but i dont know about there quality.i like ken farrells.even night force but cant find a 0 moa in night force.my scope is a bench rest 8x32x56.do you think there quailty is good enough so i dont have to bed the base?

[Warg]

do you think on a remington 700 milspec 5r rifle{a new one}i ll have to bed the base plate?plus i dont need a 20 moa,im shooting at 100 200 300 yrds.thats it.i dont think badger makes a 0 moa do they?havent seen one.egw does but i dont know about there quality.i like ken farrells.even night force but cant find a 0 moa in night force.my scope is a bench rest 8x32x56.do you think there quailty is good enough so i dont have to bed the base?

Badger does, in fact, make a zero MOA base.