AR Picture Thread

[docsherm]

Am I missing something???? Isn't this thread supposed to be for Pics of gun and not critic statements and would most likely make since with a pic or two.

[CLHC]

Gianni Comm Lately here!

[kfrank]

Am I missing something???? Isn't this thread supposed to be for Pics of gun and not critic statements and would most likely make since with a pic or two.

Where's your pics?https://www.m4carbine.net/attachment...1&d=1213501671

[Razorhunter]

Gianni Comm Lately here!

Here's a pic-shot of mine in it's simplest form. That is, as compared to all the fine lookers I'm seeing here.



That's all!

Everyone needs to start posting all the specs on their rifles! Yes, some are quite obvious, but some are not.
CL,
Which N4 is this? Is it a 16" bbl, midlength? It appears so.
I'm currently trying to decide if I want a 9" or 10" VIS on my Noveske N4 middy, but cannot find the pics of both VIS uppers with the 16" bbl.
I think Noveskes website shows the 10", but I'll have to check again.
Which one is this? 16" Low Pro I assume?

Also, is that a Vickers sling? Looks a bit wide, but not sure???

[CLHC]

Everyone needs to start posting all the specs on their rifles! Yes, some are quite obvious, but some are not.
CL,
Which N4 is this? Is it a 16" bbl, midlength? It appears so.
I'm currently trying to decide if I want a 9" or 10" VIS on my Noveske N4 middy, but cannot find the pics of both VIS uppers with the 16" bbl.
I think Noveskes website shows the 10", but I'll have to check again.
Which one is this? 16" Low Pro I assume?

Ooopps! Sorry about that, kind of a "gun shy" here in mentioning what I have. . .Okay, from Noveske Rifleworks' online site:


Noveske N4 Light Recce Low-Profile 16" (N4lr)

16.1" Cold Hammer Forged Barrel, 1 in 7" twist, 5.56mm
--Made of Mil Spec M249 Machine Gun barrel steel, with heavy M249 Chrome Lining,
(appx. 2 times as thick as an M4 or M16)
--Extended Feed Ramps
--Mil Spec Phosphate finish
--MP HP tested with certification
--Mid-Length gas system, no M203 notch
--Shot peened and MP tested bolt
--Properly staked carrier key
--Auto carrier
--Mil-Spec receiver extension, staked
--H Buffer
--Vltor Carbine buttstock [swapped for Magpul UBR]
--Tango Down pistol grip [swapped for Magpul MIAD Modular Grip - Full]
--Flat-top upper receiver
--11" free floated handguard w/ 1913 rails
--Low-profile gas block pinned to barrel
--Flip-up front and rear sights [added the LMT Front Site]
--Smith Vortex [Bold Italics, mine]
--One 30 rd mag included [it did come with only 1 (USGI?) magazine--but in addition to it, Magpul PMags]

Also added the BOBRO SHORT Vertical Fore Grip w/ SACL

Also, is that a Vickers sling? Looks a bit wide, but not sure???

Urban-E.R.T. US2 UrbanSentry Two Point/One Point Hybrid Sling is what's pictured. I'm trying this one out and liking it so far, more so than Gear Sector's GS-2P because of the quick conversion (@30 sec) on the US2 Hybrid from 2p to 1P if one chooses to do so.

Looking forward to trying out the Vickers VCAS also.

Enjoy!

[Cameron]

Great rifle CLHC!

[armakraut]

First AR in a long time, Low-speed, High-Drag... but at least it balances nice, and doesn't weigh much.

M16A1 upper, Stag Lower, PRI big-latch, Cavarms stock, Tangodown grip, blueforce sling, BCM bolt group.

[John123]

Ive been waiting on the Tango Down bipod for a while. I think my beast is finally done.








John

[CLHC]

Hey now. . .Nice!

[docsherm]

John123-

That is a great looking rifle!!! What kind of barrel is it?