Page 1 of 4 123 ... LastLast
Results 1 to 10 of 38

Thread: PWA Lower??

  1. #1
    Join Date
    Jul 2007
    Location
    SE Va, USA
    Posts
    723
    Feedback Score
    0

    PWA Lower??

    Anybody here remember the PWA (PacWestArms) lowers? I believe they were the forerunner to Olympic. Anyway, at the shop where I work, a fellow came in with a box or AR parts, enough to build 2 rifles, a 20" HBAR and a 16" carbine. The only things missing from 2 complete guns was the 20" bbl gas tube and a buffer retainer and spring. Both lowers were PWA, uppers are un marked, one w/ A2 sights and 1 w/ A1, barrels pre-ban w/ bayo lugs and threaded. I know the PWAs are pre-ban. The carbine has the old style 3-position aluminum stock, and its barrel is heavy out to the FSB and thin from there to the muzzle (pre-M4). I put them both together, using tha A2 sighted upper for the 20" gun. The 20" gun needed a new extractor spring and buffer and then worked flawlessly, even not properly lubed. I started lurking around here shortly after that so now I know it wasn't properly lubed, thank you Pat Rogers. The 16" gun has been a PITA. the upper is obviously no to spec. It needed filing on the rear tab just to close all the way, and the barrel locating notch is off. One of the triggers was too wide, so I don't believe the FCG is spec either. I got the shorty together and it has been one thing after another, it is just about working. The shop owner wanted to sell both rifles, but after so much tinkering to get the short one to work, he's not selling that one. It is basically the AR I have wanted for awhile (I don't currently have any), with the barrel profile and A1 sights and such, so I think I can get it on the cheap. I figure then I can upgrade parts to maybe end up with something worth having. I'm sure there are opinions, so I'd like to hear them. I know I can either listen or ignore, so either way I'll read them. Thanks in advance.
    NRA Life, SASS#40701, Glock Advanced Armorer
    Gunsmith for Unique Armament Creations LLC, 07/SOT

    VIGILIA PRETIUM LIBERTATIS

  2. #2
    Join Date
    Jun 2006
    Location
    Virginia
    Posts
    0
    Feedback Score
    3 (100%)
    I've owned two PWA lowers, one preban that I owned for years but traded away (very fairly) to a guy living in a ban state and one postban that I still own. I’m no expert but I remember reading PWA had some association with LMT, not Olympic. Judging by the looks of the logo & serial number engraving I would say this is correct because they look identical to my LMT lowers in every way. The two companies were also located in the same city in Illinois.

    - Both of the PWA lowers I have experience with where perfect and neither gave me any issues.
    Paul A. Hotaling
    Alias Training & Security Services, LLC
    Paul@aliastraining.com
    757-215-1959 (Mon-Fri 8AM-5PM)
    757-985-9586 (After Hours)
    www.aliastraining.com


  3. #3
    Join Date
    Jul 2007
    Location
    SE Va, USA
    Posts
    723
    Feedback Score
    0
    That could be. Info I could find was sketchy at best, so it could be wrong. From what I hear, LMT makes good stuff, better than Olympic (?). While I am familiar with the AR system and how it works, I'm not into them so much that I know all the best manufacturers. I had a parts gun built on an EA (Essential Arms) receiver way back in the 80s, but had sold it. I had bought it complete. I just recently decided I wanted another, but kind of old school, with the carry handle, A1 sights, and skinny barrel. I'm just wondering if the receiver is any good and if my build could be a reliable piece. I know, no one here knows exactly what I'm doing, so this is more a question about the possibility of this conglomeration of parts.
    NRA Life, SASS#40701, Glock Advanced Armorer
    Gunsmith for Unique Armament Creations LLC, 07/SOT

    VIGILIA PRETIUM LIBERTATIS

  4. #4
    Join Date
    Sep 2006
    Posts
    51
    Feedback Score
    0
    Quote Originally Posted by VA_Dinger View Post
    I've owned two PWA lowers, one preban that I owned for years but traded away (very fairly) to a guy living in a ban state and one postban that I still own. I’m no expert but I remember reading PWA had some association with LMT, not Olympic. Judging by the looks of the logo & serial number engraving I would say this is correct because they look identical to my LMT lowers in every way. The two companies were also located in the same city in Illinois.

    - Both of the PWA lowers I have experience with where perfect and neither gave me any issues.
    PWA were/are (?) made by LMT. I may be wrong on this, so don't take it as gospel but originally the PWA name was owned by LMT.

  5. #5
    Join Date
    Aug 2006
    Location
    Southern California
    Posts
    1,108
    Feedback Score
    0
    Quote Originally Posted by Gunfixr View Post
    The 16" gun has been a PITA. I got the shorty together and it has been one thing after another, it is just about working. The shop owner wanted to sell both rifles, but after so much tinkering to get the short one to work, he's not selling that one. It is basically the AR I have wanted for awhile (I don't currently have any), with the barrel profile and A1 sights and such, so I think I can get it on the cheap.
    Look into the gas port diameter in the barrel.
    It should be 0.062" to 0.067" maximum on a 16" carbine barrel.
    If this is an un-marked barrel, it's heritage is instantly suspect.
    I find that most un-marked barrels have oversized gas ports.
    Plugging and re-drilling makes a HUGE difference in how they perform.

    If the port is indeed oversized, there are other solutions instead of plugging and drilling.
    You can run a really heavy buffer, an adjustable gas tube or an increased-volume gas tube like the PRI fatboy.

    Reading through my how it works thread might be helpful to your understanding of the AR.
    Randall Rausch
    AR15 Barrel Guru
    California Precision Rifle Club founding member

  6. #6
    Join Date
    Aug 2006
    Location
    S. Florida
    Posts
    316
    Feedback Score
    0
    Some years ago there were a lot of PWA lowers and guns built on them at the gunshows down here. The only issue I ever saw or heard about concerning the lowers was mag wells being undersized on some. I saw a few people try a lot of GI mags in them and all very tight, so I know it wasn't the mags. Obviuosly an easy thing to check. By the time you get it running you will have gained a lot of practical experience, so if it is really cheap, why not! Good luck.

    Billy

  7. #7
    Join Date
    Jul 2007
    Location
    SE Va, USA
    Posts
    723
    Feedback Score
    0
    I read the link you provided and it explained about the gas inside the bolt carrier, but I pretty much knew the rest. I knew about case expansion and the inability to extract a case still under pressure. The barrel is not totally unmarked, it has something stamped into it on the top just in front of the FSB, I will see what it is. I only work in this shop on weekends, so I won't be there again until Sat. I will also check port size. In reading around, I see about the carbines having more issues than rifles with gas amounts and pressures. I think it's getting too much gas. It was recoiling kinda hard and overriding the next round in the mag, as if the mag couldn't keep up. I saw in Brownells this "pigtail tube" which was longer and supposed to help out with pistols and carbines. I made my own from stainless tubing (didn't want to spend $80). Theirs had 2 coils, mine had 4. It wouldn't even eject. I shortened it to 2 coils. It ejected but wouldn't pick up the next round or lock back. This to me confirms my belief that it was getting too much gas. The tubing I have is slightly thicker than the original, having an ID about .008" smaller and an OD about .01" larger. I believe it is acting like a restricter, so I have just made a straight one and will try it Sat. No, I haven't altered the FSB or the gas key, I am turning the tube to fit, and turning the gas key end to match the original. And I can run a lathe, I've been a machinist for 20 yrs. I guess at least the lower is good (maybe the only thing), but it needs a better FCG. Oh, well, I've got my FAL where I want it, I guess I need something else to play with.
    NRA Life, SASS#40701, Glock Advanced Armorer
    Gunsmith for Unique Armament Creations LLC, 07/SOT

    VIGILIA PRETIUM LIBERTATIS

  8. #8
    Join Date
    Aug 2006
    Location
    Southern California
    Posts
    1,108
    Feedback Score
    0
    Quote Originally Posted by Gunfixr View Post
    I saw in Brownells this "pigtail tube" which was longer and supposed to help out with pistols and carbines. I made my own from stainless tubing (didn't want to spend $80).
    Stay away from pigtail gas tubes.
    They move around as they heat up and cause all sorts of problems.

    Go back to a regular gas tube.
    Remove the front sight base.
    Drill down about 0.15" to 0.175" with a #43 drill bit.
    Tap this top 2/3 of the barrel wall thickness 4-40.
    Install a 4-40 x 1/8 setscrew firmly into the port until it stops against the shoulder you left at the bottom.
    Verify that the setscrew is about 0.025" to 0.050" below flush from the surface of the gas block seat.
    Peen the top of the setscrew so it's locked into place.
    Drill down through the setscrew with a 1/16" drill bit.
    Re-assemble the barrel.

    All your problems will likely be solved.

    Let us know what those markings on the barrel said.
    Randall Rausch
    AR15 Barrel Guru
    California Precision Rifle Club founding member

  9. #9
    Join Date
    Jul 2007
    Location
    SE Va, USA
    Posts
    723
    Feedback Score
    0
    Yeah, I noticed when aligning the pigtail tube that if it binds at all the coils just let it spring in and out and would probably stop the BCG in its tracks. I will note the markings on the barrel and check the hole size. I can do the 4-40 thing quite easily, especially if that will simply remedy the problem. I do appreciate this help greatly. Is there somewhere to get the specs for things like the gas hole sizes for various length barrels and such? Also, what is the recommended torque for the barrel nut? I know to grease the threads. I staked the gas key, it wasn't staked at all.
    NRA Life, SASS#40701, Glock Advanced Armorer
    Gunsmith for Unique Armament Creations LLC, 07/SOT

    VIGILIA PRETIUM LIBERTATIS

  10. #10
    Join Date
    Aug 2006
    Location
    Southern California
    Posts
    1,108
    Feedback Score
    0
    Quote Originally Posted by Gunfixr View Post
    Is there somewhere to get the specs for things like the gas hole sizes for various length barrels and such? Also, what is the recommended torque for the barrel nut?
    There is no reliable list published that I have seen.
    There are lists floating around the internet, this site even has one in a tacked thread.
    All of those lists show port sizes that are oversized in my opinion.

    I have measured literally hundreds of barrels while documenting what the different makers use.
    I have my own list, but I don't give it out freely due to the effort I have put into aquiring the info.

    Torque spec is 30ft-lbs to 80 ft-lbs as required to index.
    Grease the threads.
    Bring it to about 35 ft-lbs.
    Break the nut loose.
    Bring it to about 35 ft-lbs.
    Break the nut loose.
    Tighten it to proper alignment.
    Last edited by AR15barrels; 07-24-07 at 17:49. Reason: I like pie.
    Randall Rausch
    AR15 Barrel Guru
    California Precision Rifle Club founding member

Page 1 of 4 123 ... LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •