Page 4 of 4 FirstFirst ... 234
Results 31 to 39 of 39

Thread: KNS pins

  1. #31
    Join Date
    May 2010
    Location
    Way out!
    Posts
    154
    Feedback Score
    1 (100%)
    Quote Originally Posted by Renegade View Post
    Rotating pins is the engineered design.
    Could you explain the rationale behind engineering that pin to rotate? I'm not a gunsmith, but I am a pretty good mechanic, and I can't think of any reason for that pin to move. I'm surely missing something.

  2. #32
    Join Date
    Oct 2010
    Location
    New Mexico
    Posts
    201
    Feedback Score
    0
    You're not missing anything.
    There's no rotation engineered into the design.
    I'm sure a small amount of rotation was accounted for in the design, but there is zero reason for those pins to rotate.
    The spring captured pins are cheap to manufacture and easy to install, end of story.
    Glock uses the same design pin as their trigger pin, but it's the spring loaded slide stop lever that holds it in place.
    Last edited by JodyH; 11-30-10 at 22:07.

  3. #33
    Join Date
    Jul 2006
    Location
    Texas
    Posts
    2,827
    Feedback Score
    1 (100%)
    Quote Originally Posted by M90A1 View Post
    Could you explain the rationale behind engineering that pin to rotate? I'm not a gunsmith, but I am a pretty good mechanic, and I can't think of any reason for that pin to move. I'm surely missing something.
    If the pin does not move, then all of the stress and friction is put into a single point, in the center of the pin, which is its weakest point.

    By allowing the pins to move, the center is not stressed as above; the friction point surface area is doubled and moved to the outside of the pins, where they are strongest.

    Now in a low-rate-of-fire gun such as S/A, it might not matter much, but in a F/A gun friction is much much more severe.

    ETA:

    I do not mean rotate as 360 degrees round and round. I mean it rotates a little in conjunction with the hammer/trigger.
    Last edited by Renegade; 11-30-10 at 22:42.

  4. #34
    Join Date
    Jun 2009
    Posts
    649
    Feedback Score
    8 (100%)
    I've been using KNS pins for the last four years. I also use reduced power JP springs in my guns. In nine years of shooting ARs, I have seen two guns where one of the pins backed out causing the guns to stop working. With that thought, and the reduced power springs it gives me peace of mind knowing my pins won't back out. Beyond that they are a gimmick. YMMV
    Last edited by SpankMonkey; 12-01-10 at 08:21.

  5. #35
    Join Date
    Sep 2010
    Posts
    287
    Feedback Score
    0
    Quote Originally Posted by Coleslaw View Post
    I have seen M16's with egged pin holes. I will say these receivers had thousands upon thousands of rounds through them and were probably close to the end of their life expectancy.
    I might add they were used hard in service and had parts replaced without doubt, so poor maintenance or parts replacement practices could always play a role. Remember, some of the few receivers I have seen that had this issue had been in inventory for decades with some having had little maintainance other than a cleaning. You are shooting a weapon and you notice the pin is walking a bit. You notice the pin hole is a bit misshapen. That is it. I mean they still shot, it was not like a catstrophic failure was neccsarily immanent. The fit of the pins was just a bit loose.

    Quote Originally Posted by Eric D. View Post
    It's not something that really needs "fixed" Iraqgunz knows his stuff and if he hasn't seen an "egged out" hole from rotating pins, I believe it.
    Not doubting he hasn’t experienced deformed or damaged pin holes that he could attribute to something other than someone beating the pins back in as he stated. It is unlikely in today’s world there are any decades old M16’s in inventory that have seen hard use in a combat environment as most are destroyed as unservicable, but perhaps a few slip through the cracks, and not seeing them doesn’t mean they haven’t existed.

    So, to get back to the original question, are they necessary? No. Are they a bad idea? No. Do they work as advertised? Yes. Will most realize any benefit from them? Probably not. Would I run them on an NFA registered M16? Perhaps.

  6. #36
    Join Date
    May 2010
    Location
    Way out!
    Posts
    154
    Feedback Score
    1 (100%)
    Quote Originally Posted by Renegade View Post
    If the pin does not move, then all of the stress and friction is put into a single point, in the center of the pin, which is its weakest point.

    By allowing the pins to move, the center is not stressed as above; the friction point surface area is doubled and moved to the outside of the pins, where they are strongest.

    Now in a low-rate-of-fire gun such as S/A, it might not matter much, but in a F/A gun friction is much much more severe.

    ETA:

    I do not mean rotate as 360 degrees round and round. I mean it rotates a little in conjunction with the hammer/trigger.
    Wow, I'd like to see the engineering paper that describes that process with math. So, you're saying that all the rotational force and friction of the hammer is concentrated on the groove in the center of the pin, unless that pin is allowed to rotate a few degrees. You inadvertantly just gave the perfect reason for the KNS design, which does away with the groove. Without that groove, the pin would be many times stronger and therefore should not have to rotate, which, of course, would obviate any chance of the holes in the receiver becoming worn because of said pin rotation. With the other advantage of not ever being able to walk out, they would seem to be a "no lose" product.

    The only disadvantage I can see, is that it takes a little more time to completely strip the lower, but I can't think of any scenario where I would be in a hurry to do that anyway.

    Now, I've only witnessed, firsthand, one real world problem with an AR that the KNS pins would have prevented, but for a mere $30, I'll keep using them in my guns, just in case.

  7. #37
    Join Date
    Nov 2009
    Location
    VA
    Posts
    807
    Feedback Score
    0
    We've got quite a few auto guns that are run real real hard.

    We've experienced almost every kind of failure you can have, but NEVER a problem with walking pins or 'egged' holes.

  8. #38
    Join Date
    Nov 2010
    Posts
    491
    Feedback Score
    0
    Quote Originally Posted by Iraqgunz View Post
    In all of my years I have yet to see "egged out" lower holes from pins. What I have seen are morons who have beat on them and pounded them in, incorrectly and other silly non sense.
    EXACTLY.

    Mouth breathers who are not authorized to be working on their guns, don't have a clue, but think they do, are what causes lower holes to get "egged out" or "wallered out".

    If it is a work gun, go see your armorer.

    Same applies for installing plates with single point attachments. I cannot tell you how many guys have approached me with issued M4s with a takedown pin spring that was mashed, half sticking out and said

    "it was like that when I got it" .

  9. #39
    Join Date
    Jan 2008
    Location
    AZ-Waging jihad against crappy AR's.
    Posts
    24,902
    Feedback Score
    104 (100%)
    Actually you would be wrong as myself and many others who have been overseas have seen lowers that were originally M16A1's that were restamped and in use by National Guard and Reserve units. To include Air National Guard personnel.

    The most recent was around late 2006. Strangely enough the weapon was working fine and the holes had no issues.

    Quote Originally Posted by Coleslaw View Post
    I might add they were used hard in service and had parts replaced without doubt, so poor maintenance or parts replacement practices could always play a role. Remember, some of the few receivers I have seen that had this issue had been in inventory for decades with some having had little maintainance other than a cleaning. You are shooting a weapon and you notice the pin is walking a bit. You notice the pin hole is a bit misshapen. That is it. I mean they still shot, it was not like a catstrophic failure was neccsarily immanent. The fit of the pins was just a bit loose.


    Not doubting he hasn’t experienced deformed or damaged pin holes that he could attribute to something other than someone beating the pins back in as he stated. It is unlikely in today’s world there are any decades old M16’s in inventory that have seen hard use in a combat environment as most are destroyed as unservicable, but perhaps a few slip through the cracks, and not seeing them doesn’t mean they haven’t existed.

    So, to get back to the original question, are they necessary? No. Are they a bad idea? No. Do they work as advertised? Yes. Will most realize any benefit from them? Probably not. Would I run them on an NFA registered M16? Perhaps.



    Owner/Instructor at Semper Paratus Arms

    Facebook: https://www.facebook.com/SemperParatusArms/

    Semper Paratus Arms AR15 Armorer Course http://www.semperparatusarms.com/cou...-registration/

    M4C Misc. Training and Course Announcements- http://www.m4carbine.net/forumdisplay.php?f=141

    Master Armorer/R&D at SIONICS Weapon Systems- http://sionicsweaponsystems.com

Page 4 of 4 FirstFirst ... 234

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •