great looking setups! It seems not many people run the rifle profile LMT. I really like the look of a full rail which is why I went with the 14.5 mid with Rifle profile rail. I'd love to see some of your rifle profile MRPs
great looking setups! It seems not many people run the rifle profile LMT. I really like the look of a full rail which is why I went with the 14.5 mid with Rifle profile rail. I'd love to see some of your rifle profile MRPs
Here's my current duty set-up.
LMT complete rifle length MRP.
14.5" middy DD CHF lightweight bbl. w/ perm'd BCE 1.5. Barrel configured to MRP by DBMG LLC.
Aimpoint H-1, LT 660
Magpul stock, grip, ladder covers, AFG-2
VTAC 2 point sling, light mount, Surefire L4 light
Troy rear flip ups, DD fixed front sight
Last edited by trooper84; 02-20-11 at 16:58.
ICANHITHIMMAN when you say hk diopter sights are they genuine hk sights or are those the centurion sights?
Upper: LMT MRP
Barrel: LMT MRP 16", 1/7 twist, Mid-Length Gas System
Rail: LMT MRP Rifle Length
- AAC 51T Fast-Attach M4-2000 Muzzle Brake
- LMT Semi-Auto Bolt Carrier Group
- VLTOR/BCM Gunfighter Mod.4 Charging Handle
- KAC M4 Flip-Up Front Sight
- KAC Micro 300 Rear BUIS
- Magpul AFG
- Valk/Tac "GIT-R DONE" Ejection Port Cover
- TangoDown Rail Panels
Lower: LMT Defender 2000
- USGI Standard Trigger (6-8 lb. pull, not sure)
- LMT Ambi Selector
- Magpul MIAD Grip Full Kit
- Noveske QD End Plate
- LMT Heavy Duty QD Push Button Swivel
- Phase 5 EBRv2
- KNS Non-Rotating Trigger and Hammer Pins
- Prince50 Bullet Button (CA Compliance Part)
- Prince50 Extended Take Down Pin
Stock: LMT SOPMOD Gen. 1
- KAC M4 Sliding Buttstock Mount
- MilSpec Receiver Extension
- Standard Carbine Buffer Spring
- H1 Carbine Buffer
Magazine: Magpul PMag (CA Compliant 10/30)
Optic: Aimpoint Micro T-1 on LaRue Tactical T-1 Mount
Light: Surefire X200A with XT07 Remote Switch
Paint: None
Sling: Magpul MS2 Single Point Sling
Use: Shooting at 0-100 yards, Tactical Carbine Classes
Weight: 9lbs. 2oz. (with unloaded magazine attached)
Last edited by pacrimguru; 02-20-11 at 22:30.
LMT MRP CQB 16"...now for sale
Last edited by Rattlehead; 02-21-11 at 00:18.
Great gun, but no more pistons for me. I really wanted to give the piston guns a try in 5.56. No real benefit for me, yet a good bit heavier than my other guns. I should have replaced it with a 10.5" kit or even the 16" midlength, but just sold it instead.
12" piston on SBR'd Noveske lower. Troy BUiS. BAD Lever. MIAD. XTM panels. T1 not pictured. ASAP and MS2. Now, if I had it to do over again, I would have probably gone with a SS 16" and the S&B 1-8 when it's available. This is a great gun, but for me it makes a better precision shooter than it does a CQB gun.
Last edited by jonconsiglio; 02-21-11 at 11:16. Reason: Specs
here's my MRP configured another way too.
- magpul m93b stock
- aimpoint t-1 with 3x aimpoint magnifier
- surefire x300 with xt07 switch
- td stubby foregrip
- 14.5" barrel
Last edited by pacrimguru; 02-21-11 at 11:42.
Both 16" MRP's, will be adding a 12.5 after paperwork is done on the two factory LMT 10.5's I have incoming from Grant.
Was fooling around with Lightbox so here ya go.
Bookmarks