Page 298 of 298 FirstFirst ... 198248288296297298
Results 2,971 to 2,978 of 2978

Thread: LMT .308 MWS Pictures show us your setup

  1. #2971
    Join Date
    Feb 2013
    Location
    Colorado
    Posts
    2,317
    Feedback Score
    48 (100%)
    Quote Originally Posted by domestique View Post
    For those of you not on Instagram, FB, or ARFCOM.... we have a gun smith getting into barrel conversions for MRP, and eventually MWS barrels!

    This is huge news. We may finally get cheap plinking barrels, 6.8SPCII, Carbon PROOF barrels, more 22lr, 9mm, etc. Barrels!
    He does good work from what I've seen. He's a regular on the KAC group on FB. I don't doubt he'd do quality work with the conversions.
    "People have always been stupid. The Internet just makes it easier for us to know about them." - donlapalma

  2. #2972
    Join Date
    Dec 2006
    Location
    The South
    Posts
    3,749
    Feedback Score
    1 (100%)
    Quote Originally Posted by domestique View Post
    Marvin (who has a very long lead time), and who else?

    I know DBMG (spelling) used to, but haven't for years.
    One is/was Mark Chanlynn in CO. I think cannot recall the other. I used to have his contact about 10 years ago. A guy on arfcom had a ton of barrels converted by this smith.
    SLG Defense 07/02 FFL/SOT

  3. #2973
    Join Date
    Dec 2008
    Posts
    5,076
    Feedback Score
    7 (100%)
    Quote Originally Posted by JoshNC View Post
    One is/was Mark Chanlynn in CO. I think cannot recall the other. I used to have his contact about 10 years ago. A guy on arfcom had a ton of barrels converted by this smith.
    I think you're thinking about the now bunk DBMG. They did a number of barrels for arfcom and snipershide members years ago. I've looked for machinist to do these conversions for years, and to my knowledge Marvin Pitts at Nefarious Arms is the only game in town until D. Wilson Mfg. starts up.

  4. #2974
    Join Date
    Dec 2008
    Posts
    5,076
    Feedback Score
    7 (100%)
    Quote Originally Posted by domestique View Post
    For those of you not on Instagram, FB, or ARFCOM.... we have a gun smith getting into barrel conversions for MRP, and eventually MWS barrels!

    This is huge news. We may finally get cheap plinking barrels, 6.8SPCII, Carbon PROOF barrels, more 22lr, 9mm, etc. Barrels!

    Nice, I sent him a message last night asking about when I could send him a .22lr, and 14.5 pencil profile barrel to convert, and how much it would cost. He said it would likely be about a month until he's ready for me to send in the barrels, and he said it would cost about the same as a chop, thread, crown job, or slightly more since it take about the same time as that procedure. This is an excellent development.

  5. #2975
    Join Date
    Feb 2008
    Posts
    414
    Feedback Score
    37 (100%)
    Saw this last night on Instagram. Definitely a tempting Proof build in both 5.56 PDW fashion and possible very light weight Proof 7.62. I wish proof had 10.5 barrels though rather than 11.5. Another .22 conversion would be sweet as well.

  6. #2976
    Join Date
    Jun 2009
    Location
    AZ
    Posts
    5,461
    Feedback Score
    6 (100%)
    Quote Originally Posted by ALCOAR View Post
    Nice, I sent him a message last night asking about when I could send him a .22lr, and 14.5 pencil profile barrel to convert, and how much it would cost. He said it would likely be about a month until he's ready for me to send in the barrels, and he said it would cost about the same as a chop, thread, crown job, or slightly more since it take about the same time as that procedure. This is an excellent development.
    Thats cool. I might get a 22 inch 6.5CM or possibly PRC.

    PB
    "Air Force / Policeman / Fireman / Man of God / Friend of mine / R.I.P. Steve Lamy"

  7. #2977
    Join Date
    Dec 2009
    Posts
    50
    Feedback Score
    0
    Quote Originally Posted by ALCOAR View Post
    Nice, I sent him a message last night asking about when I could send him a .22lr, and 14.5 pencil profile barrel to convert, and how much it would cost. He said it would likely be about a month until he's ready for me to send in the barrels, and he said it would cost about the same as a chop, thread, crown job, or slightly more since it take about the same time as that procedure. This is an excellent development.
    outstanding

  8. #2978
    Join Date
    Dec 2008
    Posts
    5,076
    Feedback Score
    7 (100%)
    Quote Originally Posted by RUTGERS95 View Post
    outstanding
    He just posted up his pre order page for 10 customers.

    https://www.dwilsonmfg.com/store/p52...WKN2YihhBLqCto

Page 298 of 298 FirstFirst ... 198248288296297298

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •