Page 1 of 3 123 LastLast
Results 1 to 10 of 28

Thread: Daniel Defense MFR 12.0 Rail- A Review

  1. #1
    Join Date
    Apr 2011
    Location
    PDX
    Posts
    18
    Feedback Score
    1 (100%)

    Daniel Defense MFR 12.0 Rail- A Review

    This is an overview of the new Daniel Defense MFR 12.0 Rail that was used on a BCM light weight upper build. Other aspects of the build will also be addressed. Additonally, there will be a brief, unscientific comparison to the Troy VTAC rail

    I decided to build a second upper (which may... awe who am I kidding, will turn into another complete rifle) and chose a lighter-weight route. I waited patiently for BCM to get their 14.5" LW middies in and snatched one up when they became available. I've used their standard barrel version before and was thoroughly satisfied, so I decided to stick with them again.

    The DD MFR looked interesting and since I already had a VTAC rail on another upper, I decide to try it. There wasn't too much info out there from the end-user, so I figured I'd also take the opportunity to do a write up on it as well.

    To make the 14.5" NFA friendly, a Battlecomp 1.5 was tentatively chosen. After receiving the upper and measuring the barrel + A2, I found that my 14.5" was really a 15" (WTF over?) which was made 16 3/16" with an A2. This opened the door to other standard muzzle devices. I had previously read about the Griffin Armament M4-SD Compensator which performed nearly identically to the Battlecomp, save for a little more flash (and ~$50 less to boot), so I ordered one from Joe Bob Outfitters using code "carolina" to save a few more bucks.

    After watching surf's Youtube vid on shaving an FSB (seen here http://www.youtube.com/watch?v=I5rPPyYdFUs) I decided to give it a whirl. I practiced on a .750 FSB I had lying around then it was on to the real one. Let me say that the taper pins on this upper were UNREAL! I spent the better part of 2 hours trying to bang those SOBs out. I used a dremel briefly, and eventually went to the concrete garage floor and used a large mallet and and struck those things 10-15 times like Thor while working in profanity the way others might work in oils or clay (+10 internet points if you can name the movie).

    The MFR rail and M4-SD arrived a couple days apart and I went to a local 'smith to get the proprietary barrel nut put on and comp pinned. Here's what I came home with:




    Due to the narrowness of the barrel nut rail interface ring thingy in the rear of the rail I had to do additional contouring of the FSB. A fair warning, use a pinned low-pro gas block, set screw version, or shaved FSB as I don't believe a clamp-on style will have enough clearance.


    The railed sections provide with rail allow the user to add or remove sections with the rail mounted. Another improvement over the VTAC I have on another upper. The attachment hardware on the back of the rail section is connected to two hex head screws on the railed side. When the screws are loosened, the mounts extend away from the section so they can be slid into the holes (that's what she said) of the MFR, one after the other. Once in position, tighten the screws and you're good to go.


    While looking over the rail I didn't immediately notice an anti-rotation feature, and when looking at the mounting system, which is four set screws positioned equi-distant around the rail at 45* which sit in a 360* groove, it looked like there might have been some cause for concern.


    However, closer inspection showed that the tube extended about 1/16" past the top rail on the sides and indexed quite nicely on both sides of the upper reciever, a feature devoid of in the VTAC design.


    After sliding the rail over the barrel onto the barrel nut, it felt rather loose, as though something was not mating up correctly. Also, there was a substantial gap between the upper and tube.


    I decide to RTFI and DD mentioned this looseness as a point at which to line the tube and receiver rails up before installing the set screws. Upon tighting the set screws, the MFR was pulled back towards the upper receiver and the gap was sufficiently closed.


    Now for a brief comparison between the MFR and VTAC.


    I have been using the VTAC for several months and like it alot, but feel it could benefit from a stronger mounting system, which the MFR has. The MFR is noticeably larger than the VTAC, though not by much. The outer diameter of the MFR is 1.76" verse the 1.74" of the VTAC. Here's a measurement of the outer circumference which shows the minimal difference, about 1/16".




    I personally like the feel of the VTAC in my hands better, not necessarily due to the smaller diameter, but the channeling running the length of the rail provides for a better feel and texture not present on the MFR.

    After installing the two rails, I have much more confidence in the durability of the MFR over the VTAC, albeit at a higher price point. MSRP on the MFR is $249 but can be had for much less with some effective searching (i.e. sku/part number).



    Thanks for reading and I hope this was beneficial.
    Be ashamed to die until you have won some victory for humanity.

  2. #2
    Join Date
    Apr 2011
    Posts
    265
    Feedback Score
    2 (100%)
    Sweet review! I just ordered my URG from DD. V7 upper w/ LW 14.5" barrel. I can not wait to put it together when it gets here! Thanks for the review now get some rounds through that thing!
    ATTENTION: What you just read may very well contain sarcasm! Judge me accordingly.

  3. #3
    Join Date
    Nov 2009
    Location
    VA
    Posts
    807
    Feedback Score
    0
    good review, thanks.

    One thing- you realize barrel length measurements are taken down the bore with the action closed, right? That would explain your "extra 1/2". I just ask because if BCM makes a 14.5" bbl, it will be 14.5" (in my experience), requiring an extended device to be legal.

  4. #4
    Join Date
    Jul 2011
    Location
    Wisconsin
    Posts
    7
    Feedback Score
    1 (100%)
    Thanks for the great write-up!

    "...you'll shoot your eye out kid..." :-)
    My favorite holiday season movie!

    Sent via Tapatalk ~Android~
    You can take the Texan out of Texas, but you can't take Texas out of the Texan.

  5. #5
    Join Date
    Apr 2011
    Location
    "Adios Mofo" - TEXAS
    Posts
    421
    Feedback Score
    2 (100%)
    Very nice review! Let us know how she runs on the next outing.

  6. #6
    Join Date
    Oct 2009
    Location
    Southeast Georgia
    Posts
    1,887
    Feedback Score
    0
    Good review.
    But what then is capital punishment but the most premeditated of murders, to which no criminal's deed, however calculated it may be, can be compared? - Albert Camus

  7. #7
    Join Date
    Jun 2010
    Location
    West Tennessee
    Posts
    56
    Feedback Score
    4 (100%)
    Good review, good photography and clear explanation.
    I love my VTAC but always curious about what else is available.

  8. #8
    Join Date
    Apr 2011
    Location
    PDX
    Posts
    18
    Feedback Score
    1 (100%)
    Quote Originally Posted by JasonM View Post
    good review, thanks.

    One thing- you realize barrel length measurements are taken down the bore with the action closed, right? That would explain your "extra 1/2". I just ask because if BCM makes a 14.5" bbl, it will be 14.5" (in my experience), requiring an extended device to be legal.
    I must've measured that thing 50 times with no device and with the device before committing to the pinning, all with a CH and closed bolt. I used several different rods, from both sides and marked them twice and everything equaled out. Sounds weird, but that's how it is.
    Be ashamed to die until you have won some victory for humanity.

  9. #9
    Join Date
    Nov 2009
    Location
    VA
    Posts
    807
    Feedback Score
    0
    Quote Originally Posted by nadler20 View Post
    I must've measured that thing 50 times with no device and with the device before committing to the pinning, all with a CH and closed bolt. I used several different rods, from both sides and marked them twice and everything equaled out. Sounds weird, but that's how it is.
    I believe you. Sh!t can happen. The end result looks good

  10. #10
    Join Date
    Sep 2009
    Location
    Central Oregon
    Posts
    116
    Feedback Score
    12 (100%)
    Quote Originally Posted by Hatchie View Post
    Good review, good photography and clear explanation.
    Agreed. I've really been meaning to try the MFR but haven't gotten around to it yet, this is just more motivation.

    I can see what you mean about the TRX having more texture to it than the MFR, but also agree that sturdier mounting trumps that. I'm envisioning some skateboard tape forward of a hand stop to fix the texture issue...

Page 1 of 3 123 LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •