Page 63 of 139 FirstFirst ... 1353616263646573113 ... LastLast
Results 621 to 630 of 1387

Thread: New Noveske NSR rail!

  1. #621
    Join Date
    Sep 2011
    Posts
    130
    Feedback Score
    3 (100%)
    Just got a set of the NSR rail panels to try out today. I had a very hard time getting them on. I was forced to file down the slits inside the keymod lug to finally get them to slide in. I don't see how they can go in unless they get filed down. Once they were on, they were nice...but the process of putting them on kind of put me off. In my opinion, I shouldn't have to file them down so much just to get them on.

  2. #622
    Join Date
    Jul 2006
    Location
    Oregon
    Posts
    3,458
    Feedback Score
    2 (100%)
    The NSR panels are designed to be a tight fit, so they won't come off under hard use or be able to move around.

    It does require some effort to install or remove. The key is pushing the panel down while sliding them.

  3. #623
    Join Date
    Feb 2012
    Posts
    23
    Feedback Score
    0

    Question

    what kind of hardware is used on the attachments? Can we purchase just the hardware?

  4. #624
    Join Date
    Nov 2008
    Location
    Northern Virginia
    Posts
    716
    Feedback Score
    61 (100%)
    I cannot for the life of me get these panels installed on this rail. What did you guys file down to make them fit ?

  5. #625
    Join Date
    Sep 2011
    Posts
    130
    Feedback Score
    3 (100%)
    The little slits on each side of the lug on the underside of the panel.

  6. #626
    Join Date
    Nov 2008
    Location
    Northern Virginia
    Posts
    716
    Feedback Score
    61 (100%)
    I tried shaving those down but no success. I think the issue is the little lug right behind the keymod is too wide to go into the slot.

    I tried pushing up and then forward and the keymod part goes forward but the little lug behind it is preventing it from locking in.

  7. #627
    Join Date
    Jan 2009
    Location
    Mississippi
    Posts
    3,996
    Feedback Score
    50 (100%)
    FYI,

    If anyone wants to cut the one piece 7 section panel down shorter here is a tip. Take something similar to a dental pick and drag it relatively hard on the seam between the panels you want apart. I did this about 15 times on the backside only.
    Next place that same area over the edge of something like a table and press down on both ends. It breaks very cleanly.

    -Jax





    "Despite what your mamma told you, violence does solve problems."
    -Ryan Job



    Quote Originally Posted by Army Chief View Post
    "Elite" designations come from the things that you DO in life, and not from the things that you buy along the way. AC

  8. #628
    Join Date
    Jan 2012
    Location
    Not where I want to be!!
    Posts
    137
    Feedback Score
    0
    Got my panels today, two sets. They went on with a little effort, but no sanding or filing. Glad I ordered two, I don't see how you could do much with one set. They are really nice.

  9. #629
    Join Date
    Jul 2006
    Location
    Oregon
    Posts
    3,458
    Feedback Score
    2 (100%)
    Quote Originally Posted by SFCRoOKs415 View Post
    what kind of hardware is used on the attachments? Can we purchase just the hardware?
    Like the screws? They are a #8-32x3/8 100 deg flat head, T15 drive.

    The screw is staked on the end when it is assembled. They do not come apart to install, so you will not loose any or need spares.

  10. #630
    Join Date
    Dec 2010
    Location
    New Hampshire
    Posts
    270
    Feedback Score
    25 (100%)
    I got my NSR panels today, and I can see how some people could have an issue, But as Todd says press down as you push the panel forward..




Page 63 of 139 FirstFirst ... 1353616263646573113 ... LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •